Instruction/ maintenance manual of the product F107411-01 Aga Ranges
Go to page of 32
Elec tric R ange Ser vice Instruc tions F107411-01 ww w .aga-ranges .com This book contains man y impor tant safety messages. Always r ead and obey all safety messages.
W ARNING If the information in this manual is not follo wed exactly , a fi re ma y result causing propert y damage, personal injury or death. W ARNING The anti-tip device supplied with this range must be corr ectly fi tted when the range is installed .
3 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Sec tions Diagnostics 5 Ser vicing P roc edures 11 T echnical Data 27 Schematic.
4 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished..
5 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Diagnostics Check ing the Multifunc tion O ven 6 Check ing the Con vection O ve.
6 Check 1 Result P ossible Cause Open the oven door and turn on the o ven light Light does not work 1 No power to range 2 Light bulb failed (most likely cause) 3 F ault in power supply t o switch 4 F .
7 Check ing the Multifunc tion O ven.
8 Check 1 Result P ossible Cause Open the oven door and turn on the o ven light Light does not work 1 No power to range 2 Light bulb failed (most likely cause) 3 F ault in power supply t o switch 4 F .
9 Check ing the Con vection O ven.
10.
11 Contents 1. T o change oven light bulb . 12 2 How to Mov e the R ange for Servicing 12 3. T o Remove a Side P anel 13 4. T o Lift up the Ceramic Hob 14 5. T o replace a hob element. 15 6. T o replace a C ooktop W armer element. 15 7. T o replace the cooktop neon indicat or lights pack 16 8.
12 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Ser vicing Notes Disconnect from electricity supply before commencing servicin.
13 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Replaceing the Range Reverse proc edure to reinstall the range and low er the front roller . Make sure the an ti-tip device is re- engaged properly when the range is r eplaced.
14 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 4. T o Lift up the Ceramic Hob Pull the range f or ward. Pull off the push fi t control panel end caps at each end and remov e the end fi xing screws under the end cap .
15 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 5. T o replace a hob element. Lift up the ceramic hob see 4. The elements are now accessible . Remove the scr ew in the center of the element and slide it out to the side.
16 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 7. T o replace the c ooktop neon indicator lights pack Lift up the ceramic hob see section 4. The neon indicator light pack is held to the support bracket by two clips.
17 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 9. T o Remove Oven Light S witch Remove c ontrol panel (see 8).
18 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 12. T o Remove a Thermostat Lift up the cooktop - see 4. Remove the c ontrol panel - see 8 Remove the ov en shelves. Undo the range rear cov er screws and lift covers clear .
19 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 13. T o Change Cooktop or Broiler C ontroller Lift up the ceramic hob top (see 4). Remove c ontrol panel (see 8). Disconnect wiring from controller – make a note of the wire colors and t erminal connections.
20 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 15. T o Remove an Oven Door Door is heavy - take care. Open oven door and r emove Handyrack (where fi tted) by springing one side out of the bracket on the door and sliding the other side free.
21 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 16 T o Adjust the Oven Door Angle The ov en doors are heavy . T ransit of the range can cause the oven doors t o move so that they are not correctly aligned.
22 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 17. T o Change O ven Door Outer P anel Remove the two plastic blanking plugs from the door handles. Remov e the 4mm Hex headed screws holding the handle to the door with the hexagon key tool.
23 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 19. T o Remove the Oven Door Seal Open oven door . The seal is held in place by small hooks on the rear face . At the corner pull seal diagonally away fr om the door centre until that hook is released.
24 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 22. T o Remove an Oven Inner Back Open the oven door .
25 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 25. T o Remove the L eft Hand Multifunc tion Oven Bottom and T op Elements Bottom Element Pull the range f or ward to access the r ear of the range, see the section ‘How T o Move the Range for Servicing’ .
26 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished..
27 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. T echnical Data DA T A BADGE L OCA TION: Inside base of drawer ca vit y - remov e drawer . For r emoval of drawer see installation instructions.
28 Schematic diagram of the R ange Caution: Label all wires prior to disconnection when servicing controls . Wiring err ors can cause improper and dangerous operation.
29 Code Description BRE Broiler elements BSB Br oiler switch block BT C Broiler contr oller CFM Cooling fan motor IGS Ignition swit ches ISG Ignition spark generat or LBE Left hand bottom element LFE .
30.
31.
Aga Ranges 110 W oodcrest Road Cherr y Hill, NJ 08003 USA 1.866.4AGA.4USA ww w .aga-ranges.c om Email suppor t@aga-ranges.com.
An important point after buying a device Aga Ranges F107411-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Aga Ranges F107411-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Aga Ranges F107411-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Aga Ranges F107411-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Aga Ranges F107411-01 will certainly help you make a decision on the purchase.
If you already are a holder of Aga Ranges F107411-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Aga Ranges F107411-01.
However, one of the most important roles played by the user manual is to help in solving problems with Aga Ranges F107411-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Aga Ranges F107411-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
