Instruction/ maintenance manual of the product MODEL GL-C CMA Dishmachines
Go to page of 11
www.cmadishmachines.com 800-854-6417 FAX 714 - 8 95 - 2 141 CMA DISHMACHINES 12700 KNOTT AVENUE GARDEN GROVE, CALIFORNIA 92841 MODEL GL-C INSTALLATION & OPERATION Rev.
T ABLE OF C ONTENTS M ODEL GL-C 1. RECEIVING ................................................................................................... 2 2. SPECIFICAT IONS .....................................................................................
Receiving 1. Receiving 1. Remove the packing material from the top of the conveyor sta ck. 2. Remove all packing material and tape secu ring components within the machine. Check that both trays are positioned properly. 3. Check for the following co mpone nt parts: A.
Specifications 2. S pecifications WATER CONSUMPTION HOT WATER INITIAL FILL 3 GAL. 11.35 L. HOT WATER PER HOUR (max) 12 GAL. 45.42 L. COLD WATER PER HOUR 168 GAL.
Instructions 3. Inst allation 3.1. Electrical * A 15 Amp, 240 Volt, 60 Hz dedicated circuit should b e used to supply electrical power to the GL-C machine (see specification sheet page 2).
Flow Diagram 4. GLC Flow Diagram MODEL GL-C Installation & Operation Manual R ev. 1.00 –2/23/06 Page 5.
Operation 5. Operation 5.1. Filling the Wash Tank • Ensure that the overflow drain tube is in place in the deterg ent tank. • Flip power on-off/flush switch to the “ON” position. Th e water will fill until the proper level is reached then turn the heating element “ON”.
Operation MODEL GL-C Installation & Operation Manual R ev. 1.00A –2/23/06 Page 7 To Adjust Rinse Agent In jector : • When a new rinse agent container is installed, push the prime b utton in and hold until the rinse injector feed tube is full. • Start the washer.
Maintenance 6. Maintenance 6.1. Troubleshooting PROBLEM LIKELY CAUSE SOLUTION Power off at circuit breaker Reset circuit breaker Drive motor burn out Replace drive motor Obstruction in wash or rin se .
Maintenance MODEL GL-C Installation & Operation Manual R ev. 1.00 –2/23/06 Page 9 PROBLEM LIKELY CAUSE SOLUTION Rinse solenoid valve will not operate Check coil Check and install rebuild ki t Re.
Electrical Diagram 7. Electrical Diagram P O W E R O N / O F F R O C K E R S W I T C H H E A T E R N C N O C 1 3 6 4 7 9 B A N C N O C 1 2 4 3 5 6 8 7 T R A N S F O R M E R C O N V E Y O R M O T O R R.
An important point after buying a device CMA Dishmachines MODEL GL-C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CMA Dishmachines MODEL GL-C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CMA Dishmachines MODEL GL-C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CMA Dishmachines MODEL GL-C you will learn all the available features of the product, as well as information on its operation. The information that you get CMA Dishmachines MODEL GL-C will certainly help you make a decision on the purchase.
If you already are a holder of CMA Dishmachines MODEL GL-C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CMA Dishmachines MODEL GL-C.
However, one of the most important roles played by the user manual is to help in solving problems with CMA Dishmachines MODEL GL-C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CMA Dishmachines MODEL GL-C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
