Instruction/ maintenance manual of the product CDR 4170 Clover Electronics
Go to page of 67
INSTRUCTION MANUAL ST ANDALONE 4CH DVR DIGIT AL VIDEO RECORDER MODEL: CDR 4170 POWER FULL ALARM TIMER PLAY REC CH1 CH2 CH4 CH3 POP PIP QUAD ENTER AUTO PLAY FF REW STOP SEARCH SYS LOG SETUP WTMK BACKUP PTZ ALRST REC PAUSE ESC OSD Copyright © 2006 Clover Electronics U.
CAUTION RISK OF ELEC TRIC SHOCK. DO NOT OPEN. CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEA BLE PA RTS INSIDE.
NOTE : This equipment has been certified and found to com p ly with the limits regulated by FCC, EMC and LVD. Therefore, it is designed to provide r easonable protectio n against interference and will not cause interference with other ap pliance usage.
CONTENTS 1 . G E N E R A L P R E C A U T I O N S 1 2. SPECIFICATIONS 3 3 . O P E R A T I O N 5 3 . 1 F R O N T P A N E L 5 3.2 BACK PANEL 9 4. BASIC CONFIGURATION OF THE MONITOR SCREEN 10 4 . 1 S T A R T U P 1 0 4 . 2 L I V E S C R E E N 1 1 4 . 3 R E C O R D I N G S C R E E N 1 2 4 .
8 . I N S T A L L A T I O N 4 0 8.1 SYSTEM CONFIG URATION DIAGRAM 40 8 . 2 C A M E R A 4 1 8.3 AUDIO 41 8 . 4 M O N I T O R 4 2 9 . N E T W O R K I N G 4 3 9 . 1 R E Q U I R E M E N T S 4 3 9.2 INSTALLING THE PROGRAM TO THE PC 43 9.3 CONNECTING THE DVR TH ROUGH GUI (CLDVR) 44 9 .
1. GENERAL PRECAUTIONS 1. Read Ins tructions: All of the safety and operating instruction s should be read and understood before the product is u sed. 2. Retain Instru ctions: The safety and operating in structions should be retained for future reference.
result in damage and will often require e xtensive work by a qualified service technician to restore the product to its normal operation e. If the product has been dropped or the cabinet has been damaged f. When the product displays a distinct change in performance - this i ndicates a need for service 17.
2. SPECIFICATIONS DVR SPECIFICATIONS System NTSC or PAL (Auto Detection) Video Input 4 Inputs (BNC): 1Vp-p composite, 75 ohms Video Output 2 Outputs (BNC), 4 Looping output (BNC): 1Vp-p composite, 75 ohms Audio Input 1 Channel (RCA) Audio Output 1 Channel (RCA) Alarm Input 4 Ch alarm Inputs: Normally Open (N.
Backup JPEG & AVI File format through GUI, DVR File format at USB. Ethernet RJ-45 Connector for netwo rk communication PAN / TILT RS-4 85 Control (Pelco D Protocol) USB Port Data Backup, Firmware .
3. OPERATION 3.1 FRONT PANEL 1. HDD RACK Master HDD : Installed 160G B 2. CH 1 / LEFT - While in Quad mode, press thi s button momentarily (at least 3 seconds) and channel 1 will appear i n full screen. - In full screen mode, channel 1 single screen o r on PIP / POP / QUAD screen, press this button once and the screen will freeze.
4. CH 3 /DOWN - While in Quad mode, p ress this button momentarily (at least 3 seconds) and channel 3 will appear i n full screen. - In full screen mode, channel 3 single screen o r on PIP / POP / QUAD screen, press this button once and the screen will freeze.
10. LED FUNCTION - REC : The LED wil l blink when the system is in the recording mode. - PLA Y : The LED will blink when t he syste m is in the replaying mode. - TIMER : When the SCHEDULE RECORD is se t, the LED will blink before it start s RECORDING .
WATERMARK CHEC K - Press and hol d this button for about 3 seconds in the playback mode, the Water Mark OSD will be shown on the sc reen. To exit, press and hold this button again for about 3 secon ds.
3.2 BACK PANEL 1 2 3 4 5 6 7 8 CH1 CH2 CH3 CH4 LOOP OUT VIDEO I N V - OUT1 A - IN A - OUT ETHERNET ALARM IN 12 34 GND + _ ALARM OUT AC INPUT AC100-240V,50/60Hz POWER ATTENTION CAUTION RISQUE DE CH OC .
4. BASIC CONFIGURATION OF THE MONITOR SCREEN 4.1 START UP When the system starts up, the following pictures will be displayed in se quence. Firmware version # Hard Drive information.
4.2 LIVE SCREEN Camera Title Time and Date Full Screen in Live Mode Quad Screen in Live Mode Camera Title Indicates recordin g HDD Time and Date Indicates recordin g HDD Camera Ti tle Indicates record.
Indicates recordin g HDD Time and Date Camera Title POP Screen in Live Mode 4.3 RECORDING SCREEN Recording OSD Camera Ti tle Indicates recordin g HDD Time and Date Quad Screen in Record Mode - 12 -.
4.4 PLA YBACK SCREEN Playback OSD & Speed Time and Date Camera Title Indicates recordin g HDD Playback OSD & Speed Time and Date Camera Title Indicates recording HDD Full Screen in Playback Mo.
4.5 RECORD AND PLA YBACK SCREEN REC, Playback OSD & Spee d Time and Date Camera Title Indicates recordin g HDD Nine Screens in Record and Play bac k Mode Quad Screen in Record and Play bac k Mode .
4.6 LIVE Live means viewing the present video image s from the cameras on the monitor. 4.6.1 Full Screen display Full screen display is possible in the Live mode o r Record mode. Use channel selection button to choose a corre sponding video input. Refer to 4.
- Press the same channel sele ction button to release the freeze function. Freeze symbol 4.6.7 OSD On / Off Available in the LIVE, RECORD or PLAYBACK mode. When the OSD button is pressed, all the te xts except the REC and PB (PLAYBACK) OSD are cleared temporarily.
The whole recording lists a re updated hourly up to 1,000 lists on both Master and Slave. 4.7.3 Schedule recording Recording by schedul ed time The time of record start and finish can be set to hour: minute. Refer to section 5.7.6 for more informa tion.
4.8.3 Playback by the last recording list When the SEARCH button is pressed, the SEARCH/HDD SET menu appears on the screen. Select THE LAST RECORD LIST and press the ENTER button. It will replay from the beginning of the last recorded list. Press the ESC button to return to the SEARCH/HDD SET menu.
Set the TIME/DA TE by using the UP/DOWN buttons for changing the values an d use the LEFT/RIGHT buttons to move to next field. Press the ENTER button to search the recorded image. If the recorded image exist s, it automatically plays data an d if not, it returns to the LIVE mode.
5. SETUP 5.1 SETUP SCREEN TREE - 20 -.
- 21 -.
- 22 -.
5.2 HOW TO SET UP - Setup is possible in the LIVE mode and partly in the recording mode, not in the playback mode. - Press the SETUP button. - Choose a setup item by using the UP/DOWN buttons and press the ENTER button. - Choose the desired values with the ENTER button.
5.3.6 REC SPEED • Choose the REC SPEED in the ALARM OPTION menu by using the UP/DOWN buttons. • Choose one REC SPEED among 01, 02, 03, 05, 10, 15, 30 and 60 IPS by repeatedly pressing the ENTER button, if the REC RESOLUTIO N in the R ECORD menu set to 720H or 360H.
5.4.4 AREA • Choose the AREA in the MOT ION menu with the UP/DOWN buttons • Press the ENTER button to create the motion detection AREA . • Move the symbol “ O ” by using the UP / DOWN / LEFT / RIGHT buttons and select the area where you wo uld like to create, and press the ENTER button.
• T o apply the setting, press the ENTER button. 5.5.1.3 DATE FORMAT • Choose the DA TE FORMA T in the TIME /DA TE SET menu with the UP/DOWN buttons. • Select the DA TE FORMA T by pressing the ENTER button. There are three format s to display the time and date as follows.
by using the LEFT / RIGHT / ENTER butt on, it starts to formatting or select NO for going back to the previous mode. 5.5.2.3 HDD INFO • Choose the HDD INFO in the HARD DISK menu by using UP/DOWN buttons. • Select BYTE , PERCENT AGE or OFF by pressing the ENTER button.
5.5.6.1 IP MODE • Choose the IP MODE in the IP CONFIGURA TION menu with the UP/DOWN buttons. • Choose DYNAMIC IP or ST A TIC IP by pressing the ENTER button. DYNAMIC IP : The IP is automatically allocated via router . The refore the IP address, subnet mask and gateway address will be auto matically allocated.
5.5.6.6 MAC ID The MAC ADDRESS was consigned to each DVR at the factory . 5.5.7 NETWORK PERFORMANCE • Choose the NETWORK PERFO RMANCE in the SYSTEM menu with the UP/DOWN buttons. • Press the ENTER button and the NETWORK PERFORMA NCE window will be displayed.
5.6.2 DWELL TIME • Choose the DWELL TIME in the VIDEO menu with the UP/DOWN buttons. • Press the ENTER button, and the DWELL TIME menu will be displayed. • Select the desired channel by using UP/DOWN buttons and press the ENTER button to change the dwell time of the desired channel.
5.7.5 AUDIO REC • Choose the AUDIO REC in the RECORD menu by using UP/DOWN buttons. • Select ON or OFF by pre ssing the ENTER button. 5.7.6 SCHEDULE REC • Choose the SCHEDULE REC in the RE CORD menu by using UP/DOWN buttons. • Press the ENTER button and the SCHEDULE RECORD SET menu will be displayed.
At “ON” mode, the borderline will be shown on the screen. 5.8.3 TIME/DA TE • Choose the TIME/DA TE in the DISPLAY menu by using UP/DOWN buttons. • Select ON or OFF by pre ssing the ENTER button. At “ON” mode, the time/dat e will be shown on the screen.
5.10.1.1 PASSWORD • Select the P ASSWORD in the DVR ACCOUNT menu by using UP/DOWN buttons. • Select ON or OFF by using the ENTER button. • If ON is selected, the password has to be entere d to get into the following mode. Setup mode, Search mode, Record mo de, Record stop mode, PTZ mode and System Log mode.
• Press the ENTER button and the NETWORK ACC OUNT menu will be displayed. 5.10.2.1 USER ID • Select the USER ID in the NETWORK ACCOUNT menu by using UP/DOWN buttons. • Press the ENTER button. • Change the values up to 5 digit s with the UP/DOWN buttons and move the digits with the LEFT/RIGHT button.
5.1 1.2 HOST NAME • Choose the HOST NAME in the DDNS SET menu with the UP/DOWN buttons. • Press the ENTER button to change the values with the UP/DOWN buttons and select the digits (up to 8 digit s) by using the LEFT/RIGHT buttons. • After changin g the values, press the ENTER button.
10. T o complete, click Add Host on the bottom. 11. After registration, go to the DDNS SET menu on the DVR. 12. Refer to section 5.1 1 DDNS in this manual for the next step. Registration to CLOVERDVR.COM 1. Go to website www .c loverdvr .c om 2. Select Insert New User .
4. Attach the HDD to the removable HDD ra ck and se cure it with the supplied screws as below . 5. Assemble and put the removable HDD ra ck back in it’s place. 6. T urn the power on and see if the HDD is bei ng recognized. 6.2 INST ALL THE HDD2 The HDD2 (SLA VE) can be inst alled inside of the system.
HDD2 A TT ACHING POINT 4. Secure the HDD with the supplied screws as below . 5. Connect the power connector a nd the flat cable to the HDD. 6. Reassemble the cover . 7. T urn the power on and see if the HDD is bei ng recognized. NOTE Be sure that the jumper setting is correct.
7. PTZ CONTROL 1. Connect Pan/T ilt/Zoom camera’ s control to RS 485(+) / RS485(-) port on the rear of the system. 2. The video output of Pan /Tilt/Zoom camera to the o ne out of channel you wish to connect.
8. INST ALLA TION 8.1 System Co nfiguration Diagram The following illustration is showin g the fully inst alled system. CH1 CH2 CH3 CH4 LOOP OUT VIDEO IN V - OUT 1 A - IN A - OUT ETHERNET ALARM IN 12 .
8.2 CAMERA This product can be inst alled up to 4 cameras. Connect cameras to the VIDEO IN (BNC) on the back panel of the product. T o connect a PTZ camera, conne ct the PTZ camera’s control line to the RS-485 (+, -) termi nal and connect the video output to one out of VIDEO IN on the back p anel of the product.
CH1 CH2 CH3 CH4 LOOP OUT VIDEO IN V - OUT 1 A - IN A - OUT ETHERNET ALARM IN 12 34 GND + _ ALARM OUT AC INPUT AC100-240V,50 /60Hz POWER ATTENTION CAUTION RISQUE DE CHOC ELECTROIQUE NE PAS ENLEVER DO N.
TIME LAPS VCR CH1 CH2 CH3 CH4 LOOP OUT VIDEO IN V - OUT 1 A - IN A - OUT ETHERNET ALARM IN 12 34 GND + _ ALARM OUT AC INPUT AC100-240V,50 /60Hz POWER ATTENTION CAUTION RISQUE DE CHOC ELECTROIQUE NE PA.
How to install the client program (CLDVR) 1. Start the operating s ystem (Windows 98/2000/X P). 2. Insert the program C D into CD-ROM d rive. 3. Open My Computer , and then select CD-ROM drive. 4. Selec t the CLDVR folder, and then double click SetupCLDVR .
The following CONFIG screen will be shown. • Enter the IP/URL , Port number (default: 5700) and ID (default: admin), which must be the same as for DVR. NOTE: ■ If the registered Host Name is CL OVER1 1 at www .dyndns.org , enter clover1 1.dyndns.org in IP/URL.
1 2 3 4 2 clover.cloverdvr .com 1. CONNEC TION STATUS IND ICATOR It indicates that is curren tly being connected IP address and b andwidth (transmission speed). 2. FUNCTION OF BUTTONS Refer to next section. 3. LED DISPLAY, CLOCK The LED is lit depends on mode such as LIVE , PLAYBACK and RECOR D.
1. F/W (FIRMWARE) The FIRMWARE can be up graded by pressing the F/W button or USB device. This button is not for users, only for manufacture rs and distribution center . 2. SAVE • Click the SAVE button to save the video images that is cu rrently being displayed on the GUI.
a d m i n 4 1 3 2 1. Select the HDD (Master or Slave) 2. Select 1 out of the lists for setting up the B ackup Start Time . 3. Setup the B ackup End Time and click on blank box. If the End Time is not selected, the BACKUP continues until the Playback automatically ends.
Select Channel Reset button 7. PRINT • Click the PRINT button to print the current pictures shown on the GUI and then the following window pops up along with “ WAIT …” . Please wait a couple of second s until the system loa ds data to print. 8.
10. QUAD BUTTON • Click the Quad button to dis play the quadrant pictures. 11. AUTO BUTTON • The GUI will be viewed a f ull screen at a time in a continuous sequence (one camera after another) by click ing this button. • The dwell time can be s et from 1 to 10 seconds in the SET UP menu on the GUI .
on the window and press t he Update REC.Quality button to save them. • Installed HDD and Recording HDD: Shows currently installed HDD info rmation such as connection information, whole capa city and used space. It shows currently being recorded HDD as well.
1. Select HDD (Master/Slave) you wish to search. 2. Choose one of recordi ng lists, which are updated hourly up to 1,000 lists on both Master and Slave. 3. Click the Play button to replay the selected list, or double click the selected list to replay.
16. REW • Press this button to rewind the recorded images. • The speed will be increa sed up to x16 speed when you keep clicking this button . • The speed is shown below the buttons. 17. PLAY Press this button to replay from the begi nning of the first recording list on HDD.
9.5.2 PTZ CONTROL The following picture enable s you to control PTZ camera connect ed to the system . ZOOM control P A N control FOCUS control TIL T control PAN/TILT CONTROL Press UP key for TILT UP , DOWN key for TILT DOWN , LEFT key for PAN LEFT and RIGHT key for PAN RIGHT .
3. Click in the box of WATER MARK to put WATER MARK while repla ying (See s ection 9.5.1 #14 setup for more details). 4. Select TV system between NT SC and PAL dependi ng on the broad casting system in your country ( NTSC in USA ).
APPENDIX 1. RECORDING TIME TABLE (DAYS) 1.1 REC RESOLUTION (720H ) / REC QUALITY (VERY HIGH) SPEED 40G HDD 80G HDD 120G HDD 200G HDD 01 IPS 15-Days 19-Hours 31-Days 12-Hou rs 47-Days 07-Hours 78-Days .
30 IPS 1-Days 00-Hours 2-Days 00-H ours 2-Days 22-Hours 4-Days 22-Hours 60 IPS 12-Hours 1-Days 00-Hours 1-Days 12-Hours 2-Days 12-Hours 1.5 REC RESOLUTION (360H ) / REC QUALITY (VERY HIGH) SPEED 40G H.
10 IPS 4-Days 17-Hours 9-Days 09-Hour s 14-Days 02-Hours 23-Days 09-Hours 15 IPS 3-Days 02-Hours 6-Days 07-H ours 9-Days 09-Hours 15-Days 14-Hou rs 30 IPS 1-Days 14-Hours 3-Days 02-H ours 4-Days 17-Hours 7-Days 19-Hours 60 IPS 19-Hours 1-Days 12-Hours 2-Days 07-Hours 3-Days 22-Hours 1.
[1-2] TIME : T ime does not get initialization . [1-3] DA TE FORM : MM/DD/YYYY [1-4] DA TE : Date does not get initialization. [2] HARD DISK [2- 1] HDD1 : Shows information on HDD that is connected to HDD1. [2- 2] HDD1 : Shows information on HDD that is connected to HDD2.
[6-1] SCHEDULE REC : OFF [6-2] SCHEDULE REC SETTING : No setup data 6] DISPLA Y [1] TITLE DISPLA Y : ON [2] BORDER LINE : ON [3] TIME / DA TE : ON [4] POSITION : BOTTOM 7] BUZZER [1] KEY BUZZER : ON [.
- Check the brightness and contrast level of the monitor . 4. CHANNEL IS IN BLACK & WHITE MODE - Check the cameras. RECORDING RELA TED PROBLEMS 1. CORDING UNA V AILABLE - Adjust the camera screen. - Check recording speed or recordi ng schedule. - Adjust the system.
Limited 2Y ear W arranty This warranty gives the original purchaser specific legal rights and you ma y also have other rights, whic h may vary from state to state. If our products do not function because of any defect in material or workmanship, we will repair it for free for 2 year on pa rts a nd labor from the date of original purchase.
An important point after buying a device Clover Electronics CDR 4170 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Clover Electronics CDR 4170 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Clover Electronics CDR 4170 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Clover Electronics CDR 4170 you will learn all the available features of the product, as well as information on its operation. The information that you get Clover Electronics CDR 4170 will certainly help you make a decision on the purchase.
If you already are a holder of Clover Electronics CDR 4170, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Clover Electronics CDR 4170.
However, one of the most important roles played by the user manual is to help in solving problems with Clover Electronics CDR 4170. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Clover Electronics CDR 4170 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
