Page doesn't exist.

Cleveland Range SET-10 manual

Instruction/ maintenance manual of the product SET-10 Cleveland Range

File size: 1.09 mb
Number of pages: 25

Download as PDF

Go to page of 25

Summary of contents each page of manual

Page 1

SE95031 rev . 4 1333 East 179th S t., Cleveland, Ohio, U.S.A. 441 10 Phone: (216) 481-4900 Fax: (216) 481-3782 Visit our web site at www .clevelandrange.
Page 2

FOR THE USER IMPOR T ANT THE INST ALLA TION AND CONNECTION MUST COMPL Y WITH THE LOCAL AND NA TIONAL ELECTRICAL CODES. ENSURE ELECTRICAL SUPPL Y CONFORMS WITH ELECTRICAL CHARACTERISTICS SHOWN ON THE RA TING LABEL ALL SERVICE MUST BE PERFORMED BY A QUALIFIED CLEVELAND RANGE TECHNICIAN.
Page 3

GENERAL INFORMA TION These instructions must be retained by the owner/user for future r eference. The serial plate is located on the right side of the control housing. V oltage, phase, amperage and wattage are stated on the plate. This equipment is built to comply with applicable standards for manufactur ers.
Page 4

INST ALLA TION CLEARANCES This unit must be installed in accordance with the following clearances in order to pr ovide proper operation and servicing of the appliance. Also, it is recommended the unit be installed with suf ficient clearances to provide pr oper cleaning and maintenance.
Page 5

OPERA TING INSTRUCTIONS 1. Ensure that the electrical supply to the skillet is turned on. 2. Before cooking, be sur e that the skillet's cooking surface is clean, and that the skillet is in the fully lowered position. 3. Place the skillet's power on/off switch to the "on" position.
Page 6

CARE AND CLEANING Cooking equipment must be cleaned regularly to maintain its fast, efficient cooking performance and to ensure its continued safe, r eliable operation. The best time to clean is shortly after each use (allow unit to cool to a safe temperature).
Page 7

ST AINLESS STEEL EQUIPMENT CARE AND CLEANING (Supplied courtesy of Nafem. For more information visit their web site at www .nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. Corrosion on metals is everywhere. It is r ecognized quickly on iron and steel as unsightly yellow/orange rust.
Page 8

F AUCET ASSEMBL Y , SET -10 & SET -15 ITEM P ART DESCRIPTION QTY . NO. NO. A SPK15 Single Pantry Faucet Kit for SET -10 DPK15 Double Pantry Faucet Kit for SET -10 (Includes items 1-10) . . . . . . . . . . . . . 1 B SPK16 Single Pantry Faucet Kit for SET -15 DPK16 Double Pantry Faucet Kit for SET -15 (Includes items 1-10) .
Page 9

MODEL SET -10 SKILLET BOTTOM (for units built prior to August 2007) ITEM NO. P ART NO. DESCRIPTION QTY . 1 SK2231500 SPHERICAL WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2 F A21024 5/16-18 HEX. NUT .
Page 10

ITEM NO. P ART NO. DESCRIPTION QTY . 1 SK00008 P AN WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 F A 1 1 1 4 5 1 0 / 3 2 X 3 / 8 C R O S SH E A DS C R E W ...............................
Page 11

ITEM NO. P ART NO. DESCRIPTION QTY . 1 F12 SCREW , COVER, 10 - 24 X'/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 S K 2 2 3 4 2 0 0 S P R I N G ........................................................ 1 3 K E 5 2 1 9 2 W A S H E R .
Page 12

MODEL SET -10 ASSEMBL Y DRA WING (for units built after August 2007) 5A 5B 5C 5D 48.
Page 13

ITEM NO. P ART NO. DESCRIPTION QTY . 2 SK2238099 TIL T STOP SHAFT ASS'Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5A SK2238200 COMPONENT PLA TE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 14

MODEL SET -15 SKILLET BOTTOM & COVER VENT CAP 19 20 ITEM NO. P ART NO. DESCRIPTION QTY . 1 SK2211500 Screw , 1/4”-20 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 F A 3 0 5 0 5 - 1 W a s h e r .
Page 15

MODEL SET -15 SKILLET CONTROL HOUSING (for units built prior to November 2005) ITEM NO. P ART NO. DESCRIPTION QTY . 1 SK2274900 Cover , Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE54846-3 Gasket, Control Box Cover .
Page 16

ITEM NO. P ART NO. DESCRIPTION QTY . 1 KE001075 BOX WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 KE001074 COMPONENT PLA TE ASSEMBL Y . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 17

ITEM NO. P ART NO. DESCRIPTION QTY . 1 KE000851 BASE WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 SK00348 SUPPORT BAR ASS'Y , L.H. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 18

SER VICING GUIDE This section contains servicing information intended for use by Authorized Service Personnel. A/ PROBLEM: Skillet fails to heat with pilot light on. Probable Cause T est and Remedy 1. Faulty contactor(s) Check coil(s) and contacts of contactor(s).
Page 19

HEA TING ELEMENT REMOV AL 1. Tilt the skillet forward to access bottom cover plate. 2. Make sure power switch and external circuit br eaker (at fuse box or breaker panel) ar e off. 3. Remove screws fr om bottom cover plate. Remove plate. 4. Remove all 7/16 inch nuts and washers from stainless retaining plate located at r ear of skillet pan.
Page 20

WIRING DIAGRAM, SET -10 & SET -15 208, 220 or 240V , Single or Thr ee Phase (for units built prior to November 2005).
Page 21

WIRING DIAGRAM, SET -10 & SET -15 208/380 or 240/415V , Thr ee Phase Y Connected (for units built prior to November 2005).
Page 22

WIRING DIAGRAM, SET -10 & SET -15 480V , Single or Thr ee Phase (for units built prior to November 2005).
Page 23

WIRING DIAGRAM, SET -10 & SET -15 208, 220 or 240V , Single or Thr ee Phase (for units built after November 2005).
Page 24

WIRING DIAGRAM, SET -10 & SET -15 208/380 or 240/415V , Thr ee Phase Y Connected (for units built after November 2005).
Page 25

WIRING DIAGRAM, SET -10 & SET -15 480V , Single or Thr ee Phase (for units built after November 2005).

Read the Cleveland Range SET-10 manual - avoid problems

An important point after buying a device Cleveland Range SET-10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:

to know how to properly use the device
to know how to perform maintenance/ periodic checks of correct operation of the product Cleveland Range SET-10
to know what to do in case of failure Cleveland Range SET-10

If you have not bought Cleveland Range SET-10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cleveland Range SET-10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cleveland Range SET-10 you will learn all the available features of the product, as well as information on its operation. The information that you get Cleveland Range SET-10 will certainly help you make a decision on the purchase.

If you already are a holder of Cleveland Range SET-10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cleveland Range SET-10.

However, one of the most important roles played by the user manual is to help in solving problems with Cleveland Range SET-10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cleveland Range SET-10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center

Other manuals from the category Fryer