Instruction/ maintenance manual of the product AEG-WR Aegis Micro
Go to page of 12
Model AEG -WR Wireless Receiver Installation Manual - http://www.guardianalarms.net.
2 CONTENTS DESCRIPTION 3 COMPATIBLE TRANSMITTERS 3 INSTALLATION 4 OPERATION 5 RESET MEMORY 9 AEGIS SET UP 9 CONTROLLER INDICATIONS 10 FCC NOTICE 11.
3 DESCRIPTION The Model AEG - WR Supervised Wireless Receiver allows up to 64 unique wireless security transmitters to report information to an Ae gis automation controller. The wireless transmitters replace wired door and window sensors, as well as wired smoke, motion, and glassbreak detectors.
4 up to four transmitters assigned to it depending on the number of addresses assigned to the receiver. The 6 4 transmitters are divided into 4 groups of 16, with the transmitters in each group numbered 1 - 16. One or more groups respond to each address assigned to the receiver.
5 Place the cover on the receiver and install the antenna onto the antenna connector. Connect the receiver to the controller using 4 conductor 22 gauge or larger wire as follows: OPERATION The two operating modes of the receiver are "Run" and "Set Up".
6 (not ready) or that have trouble. The transmitter number flashes on the display followed by the status condition(s). LED DISPLAY INFORMATION ABOUT THE LED DISPLAY 1.10 Displays the number of the transmitter with a change in condition. A L Displays that the current transmitter is "NOT READY ".
7 The Set Up mode is used to configure the general operation of the receiver, to program a transmitter into the receiver, and to change the characteristics of a programmed transmitter. The Mode LED does not blink in Set Up mode. To enter the Set Up mode, press and hold the Mode/Advance switch for approximately two seconds.
8 The next four items allow you to change each digit of your security code. The Set switch is used to increment the value of each digit. The Mode/Advance switch is used to enter each digit and advance to the next. Next, the programmed characteristics o f each transmitter is displayed.
9 Once a transmitter is programmed into an address, the transmitter address will briefly turn off whenever a transmission from that transmitter is received. This can be used to verify that the correct transmitter has been programmed and is o perating reliably.
10 If Expansion Enclosures are also being used, set "NUMBER OF EXP ENCL:" to the number of expansion enclosu res plus the number of addresses used by the receiver. Set the addresses for the expansion enclosures and receiver so that they don't overlap.
FCC NOTICE This device complies with FCC Ru les Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
QUICK - REFERENCE SETUP GUIDE To Enter Set Up mode, press and hold the Mode/Advance switch for 2 seconds. DISPLAY DESCRIPTION SET SWITCH MODE/ADVANCE SWITCH C 0 Enter the first digit of the code I ncrements the digit (0 - 9) Advances to the next digit C 0.
An important point after buying a device Aegis Micro AEG-WR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Aegis Micro AEG-WR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Aegis Micro AEG-WR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Aegis Micro AEG-WR you will learn all the available features of the product, as well as information on its operation. The information that you get Aegis Micro AEG-WR will certainly help you make a decision on the purchase.
If you already are a holder of Aegis Micro AEG-WR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Aegis Micro AEG-WR.
However, one of the most important roles played by the user manual is to help in solving problems with Aegis Micro AEG-WR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Aegis Micro AEG-WR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
