Instruction/ maintenance manual of the product CFP-200 Clarke
Go to page of 36
Form No. 70880A 9/05 Clarke ® Printed in the U.S.A. READ THIS BOOK CAUTION: Read the Operator's Manual before using the appliance. This book has important information for the use and safe operation of this machine.
Page -2 - Clarke ® Operator's Manual - CFP Polisher CONTENTS OF THIS BOOK Important Safety Instructions .............................................................................................. 5 Introduction ...............................
Clarke ® Operator's Manual - CFP Polisher Page - 3 - INDICE Instrucciones de seguridad para el operador .......................................................................... 7 Presentación de la máquina ...................................
Page -4 - Clarke ® Operator's Manual - CFP Polisher LISEZ CE MANUEL ATTENTION : Lire le manuel d'utilisation avant de faire fonctionner l'appareil. Il contient des informations importantes pour une utilisation correcte de la machine, en toute sécurité.
Clarke ® Operator's Manual - CFP Polisher Page - 5 - OPERA TOR SAFETY INSTRUCTIONS W ARNING A VERTISSEMENT ADVERTENCIA DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner's Manual are ignored or are not adhered to.
Page -6 - Clarke ® Operator's Manual - CFP Polisher WARNING: Use of this machine as a step or furniture could result in injury or damage. Do not use this machine as a step or furniture. Do not ride on this machine. WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this machine.
Clarke ® Operator's Manual - CFP Polisher Page - 7 - W ARNING A VERTISSEMENT ¡ A VISO ! INSTRUCCIONES PARA LA SEGURIDAD DEL OPERADOR ¡ PELIGRO ! : Si no sigue la indicación PELIGRO , se pueden causar lesiones graves, incluso mortales. Lea y siga todas las indicaciones PELIGRO que se encuentran en el libro y en la máquina.
Page -8 - Clarke ® Operator's Manual - CFP Polisher ¡ AVISO ! Use siempre un cable con tres conductores puestos a tierra. Para una protección óptima, conecte la máquina con una caja de enchufe conectada con la red que tiene un diferencial. Si tiene alguna duda, sírvase acudir a un eléctrico cualificado.
Clarke ® Operator's Manual - CFP Polisher Page - 9 - INSTRUCTIONS POUR LA SECURITE DE L’OPERATEUR W ARNING A VERTISSEMENT ¡ A VISO ! ! DANGER ! Le non-respect des consignes précédées du mot DANGER peut occasionner des blessures graves, voire entraîner la mort.
Page -10 - Clarke ® Operator's Manual - CFP Polisher AVERTISSEMENT Utiliser toujours un câble à trois conducteurs, relié à la terre. Pour une protection optimale, branchez la machine sur une prise réseau équipé d’un différentiel. En cas de doute, veuillez faire appel à un électricien qualifié.
Clarke ® Operator's Manual - CFP Polisher Page - 11 - ACCESSORIES The following accessories are available. 1. Polishing and waxing brushes. 2. Brushes with natural or synthetic bristles for scrubbing. 3. Brushes with steel wire bristles. 4. Synthetic pad holders.
Page -12 - Clarke ® Operator's Manual - CFP Polisher ACCESORIOS Los accesorios siguientes son disponibles : 1. Cepillos para encerar y pulir. 2. Cepillos para fregar con filamentos en fibras naturales o sintéticas. 3. Cepillos de alambre de acero.
Clarke ® Operator's Manual - CFP Polisher Page - 13 - ACCESSOIRES Les accessoires suivants sont disponibles: 1. Brosses pour cirer et polir 2. Brosses de récurage, avec brins en fibres naturelles ou synthétiques. 3. Brosses avec brins en acier 4.
Page -14 - Clarke ® Operator's Manual - CFP Polisher Machine Specifications Model CFP 170 CFP 170 CFP 1700 CFP 1700 Part Number 01280A 01310A 01320A 01350A Voltage (Volts) 1 2 0 2 3 0 1 2 0 2 3 0 Frequency (Hz) 6 0 5 0 6 0 5 0 Current (Amps) 12.
Clarke ® Operator's Manual - CFP Polisher Page - 15 - Especificaciones de la pulidora Modelo CFP 200 CFP 200 CFP 2000 CFP 2000 DS Número de código 01360A 01390A 01400A 01430A Tensión (V) 1 2 0 23 0 12 0 1 2 0 Frecuencia (Hz) 6 0 5 0 6 0 6 0 Corriente (A) 12.
Page -16 - Clarke ® Operator's Manual - CFP Polisher Spécifications de la cireuse de CFP Modèle CFP 170 CFP 170 CFP 1700 CFP 1700 Numéro de code 01280A 01310A 01320A 01350A Tension (volts) 12 0 2 3 0 1 2 0 2 3 0 Fréquence (Hz) 6 0 5 0 6 0 5 0 Courant (Amps) 12.
Clarke ® Operator's Manual - CFP Polisher Page - 17 - NOTES.
Page -18 - Clarke ® Operator's Manual - CFP Polisher HOW TO PREPARE THE MACHINE FOR OPERATION UNCRATE THE MACHINE When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected.
Clarke ® Operator's Manual - CFP Polisher Page - 19 - PREPARACION DE LA MAQUINA PARA TRABAJAR DESEMBALAJE DE LA MÁQUINA Cuando reciba la màquina, inspeccione con cuidado la caja de embarque y la máquina, para verificar si hay algún daño. Si hay algún daño evidente, guarde la caja de embarque de modo que se la pueda inspeccionar.
Page -20 - Clarke ® Operator's Manual - CFP Polisher Figure 3 Figure 3a Figure 3b 120 VOL T MACHINES Instructions for connection to the power supply and the electrical ground.
Clarke ® Operator's Manual - CFP Polisher Page - 21 - INSTRUCCIONES PARA LA CONEXION ELECTRICA DE LA MAQUINA La máquina debe ser puesta a tierra. En caso de mal funcionamiento o de avería, el hilo de tierra es un camino de menor resistencia que permite el paso de corriente ; por lo cual se reduce el riesgo de choque eléctrico.
Page -22 - Clarke ® Operator's Manual - CFP Polisher Figure 4 HOW TO OPERATE THE MACHINE OPERATION (F igure 4) 1 Unwrap the Power Cord (5) and plug it into a properly grounded outlet. 2 Pull up on the Handle Release Compression Lever (4). Move the Operator Handle (6) downward until your arms are almost straight.
Clarke ® Operator's Manual - CFP Polisher Page - 23 - FUNCIONAMIENTO DE LA MAQUINA FUNCIONAMIENTO (F igura 4) 1 Desenrolle el cable de energía (5) y enchúfelo en una toma con adecuada conexión a tierra. 2 Tire de la palanca de compresión para aflojar la manija hacia arriba (4).
Page -24 - Clarke ® Operator's Manual - CFP Polisher NOTES.
Clarke ® Operator's Manual - CFP Polisher Page - 25 - CFP Series 120V & 230V Section II Part s and Service Manual (70081A).
Page -26 - Clarke ® Operator's Manual - CFP Polisher TROUBLESHOOTING SWIRLS ON THE FLOOR AFTER SCRUBBING • Floor not clean. • Incorrect solution. • Area not properly swept - debris in pad or brush. • Improper pad or brush for the job. • Moving the machine too fast.
Clarke ® Operator's Manual - CFP Polisher Page - 27 - DIAGNOSTIC TRACES SUR LE SOL APRÈS RÉCURAGE • Le sol n’est pas propre. • Solution incorrecte. • Le zone n’a pas été correctement balayée - débris sur le patin ou la brosse. • Patin ou brosse incorrect pour la tâche.
Page -28 - Clarke ® Operator's Manual - CFP Polisher Clarke ® CFP 170, 1700, 200, 2000, 2000 DS Assembly Drawing 9/05 5 1 2 3 4 6 9 12 11 10 14 20 15 26 28 27 25 29 21 22 19 18 17 16 13 8 7 23 .
Clarke ® Operator's Manual - CFP Polisher Page - 29 - Ref. Part No. Description Qty. 1 21075A Handle, Back 1 2 10687A Module, Interlock 1 3 21074A Handle, Front 1 4 71020A Label, Handle 1 5 8028.
Page -30 - Clarke ® Operator's Manual - CFP Polisher Clarke ® CFP 170, 1700, 200, 2000 Motor Assembly Drawing, Parts List and Schematics 9/05 MODEL CFP- 170, 200 170, 200 1700, 2000 1700 VOLTS / Hz 120 / 60 230 / 50 120 / 60 230 / 50 MOTOR PART NUMBER 40761A 40762A 40763A 40765A Part No.
Clarke ® Operator's Manual - CFP Polisher Page - 31 - Clarke ® CFP 170, 1700, 200, 2000 Gearbox Assembly Drawing & Parts List 9/05 MODEL CFP- 170, 200 170, 200 1700, 2000 1700 VOLTS / Hz 120 / 60 230 / 50 120 / 60 230 / 50 GEARBPX PART NUMBER 53645A 53645A 53646A 53646A Ref.
Page -32 - Clarke ® Operator's Manual - CFP Polisher Clarke ® CFP-2000DS Motor Assembly Drawing, Parts List and Schematic 7/05 Ref Part No. Description Qty.
Clarke ® Operator's Manual - CFP Polisher Page - 33 - Clarke ® CFP-2000DS Gearbox Assembly Drawing & Parts List 9/05 Ref Part No. Description Qty.
NOTES.
CLARKE PRODUCT SUPPORT BRANCHES U. S. A. Locations European Locations CORPO PRODUCTION F ACILITIES Clarke ® , Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (479) 750-1000 Customer .
Clarke ® LIMITED U.S. W ARRANTY This Clarke Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of five years from the date of purchase, when operated and maintained in accordance with Clarke's Maintenance and Operations Instructions.
An important point after buying a device Clarke CFP-200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Clarke CFP-200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Clarke CFP-200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Clarke CFP-200 you will learn all the available features of the product, as well as information on its operation. The information that you get Clarke CFP-200 will certainly help you make a decision on the purchase.
If you already are a holder of Clarke CFP-200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Clarke CFP-200.
However, one of the most important roles played by the user manual is to help in solving problems with Clarke CFP-200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Clarke CFP-200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
