Instruction/ maintenance manual of the product MS2000 Clarion
Go to page of 16
.
C ongratulations on your purchase of this Ungo System. Please read this manual thoroughly to familiarize yourself with your system’s components and operation. Discuss any questions you might have with your installing dealer. Record the serial number of your Ungo system and keep all dealer records and receipts.
Table of Contents 1. About Your Ungo Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 2. Remote Transmitters Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
Ungo Security Systems are state-of-the-art vehicle protection systems equipped with features designed to: p Deter potential intrusions to the vehicle by continually flashing the system LED status indicator while the system is Armed, giving a visual indication to any passer-by that the vehicle is equipped with a security system.
Page 2 - MS2000 Owner’s Manual Remote Transmitter Layout The Ungo MS2000 comes with 2 multi-function Remote Transmitters used to control nearly all of the system’s features. Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is taking place.
MS2000 Owner’s Manual - Page 3 Battery Replacement Your Ungo Remote Transmitter uses a 12 volt alkaline battery, which will need to be replaced from time to time. Under normal conditions, the battery may last for up to a year before it needs replacement.
Page 4 - MS2000 Owner’s Manual Remote Arming When Armed, the system monitors and protects 3 independent areas, or zones , including the doors, hood/trunk, and shock sensor. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. • The siren/horn will chirp once.
MS2000 Owner’s Manual - Page 5 To Bypass the sensors: 1. After arming the system, press Button 1 again on the Remote Transmitter within 5 seconds. • The siren will chirp 5 times, indicating the sensors have been bypassed. 2. The sensors will remain bypassed until the next time the system is armed.
Page 6 - MS2000 Owner’s Manual To set the Arming Mode: 1. Turn the ignition on. 2. Within 4 seconds, press Button 3 to change the setting. one chirp = Passive Arming with chirp two chirps = Active Arming three chirps = Passive without chirp 3. Turn the ignition off to save your selection.
MS2000 Owner’s Manual - Page 7 Emergency Override In case your Remote Transmitter becomes inoperable, or it is lost or stolen, you can still enter and drive your car by using the following procedure. Be sure that you have your ignition keys ready and that you know the location of the Override switch before you perform this procedure.
Page 8 - MS2000 Owner’s Manual Valet Mode Allows you to temporarily disable the security system when the car is being service or turned over to a parking attendant. To turn Valet Mode on or off: 1. Turn on the ignition. 2. Press and hold the override switch.
MS2000 Owner’s Manual - Page 9 To operate the Auxiliary Function with the system Disarmed , press Button 3 for three seconds. • This function will stay active for as long as Button 3 is held.
Page 10 - MS2000 Owner’s Manual Technical Data Specifications Main Unit Voltage: 12v, negative ground Current Consumption: <15mA Temperature Range: -40 o F to +257 o F Auxiliary Output Capability: 500mA Internal Relays: (1) 30A, (1) 15A Transmitter Current Consumption: <.
MS2000 Owner’s Manual - Page 11 1. Ungo Security Corporation of Gardena, California ("Ungo Security") warrants this Ungo system to be free from defects in materials and workmanship and to comply with Ungo Security’s applicable printed specifications.
Ungo Security Corporation A Clarion Company 661 West Redondo Beach Blvd. Gardena, CA 90247 800-Go-Clarion www.clarion-usa.com © Ungo Security Corporation, Gardena, CA 97-MS2000-10 Rev.
An important point after buying a device Clarion MS2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Clarion MS2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Clarion MS2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Clarion MS2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Clarion MS2000 will certainly help you make a decision on the purchase.
If you already are a holder of Clarion MS2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Clarion MS2000.
However, one of the most important roles played by the user manual is to help in solving problems with Clarion MS2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Clarion MS2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
