Instruction/ maintenance manual of the product PA-FE-TX Cisco Systems
Go to page of 64
170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Cisco Systems, Inc. Corporate Headquarters Tel: 800 553-NETS (6387) 408 526-4000 Fax: 408 526-4100 P A-FE-TX and P A-FE-FX F ast .
Access Registrar, AccessPath, Any to Any, AtmDirector, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco Certified Internetwork Expert logo, CiscoLink , the Cisco Management Conn.
Preface v Pref ace This preface explains the objecti v es and organization of this document and ho w to find additional information on related products and services.
Organization vi PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration Organization This document is organized into the follo wing chapters: Related Documentation Y o.
Preface vii Related Documentation • For hardware installation and maintenance information on Cisco 7100 series routers, refer to the Cisco 7100 Series VPN Router Installation and Configuration Guide publication that shipped with your Cisco 7100 series router .
Cisco Connection Online viii PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
CHAPTER Overview 1-1 1 Ov er vie w This chapter provides physical and functional o vervie ws of the P A-FE-TX and P A-FE-FX Fast Ethernet 100BaseT port adapters.
Port Adapter Locations on the Supported Platforms PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-2 Figure 1-2 P A-FE-FX Port Adapter—Faceplate Vie w The P.
Overview 1-3 Port Adapter Locations on the Supported Platforms Figure 1-4 VIP2-50 with T wo P or t Adapters Installed—Horizontal Orientation In Cisco 7200 series routers, port adapter slots are numb.
Port Adapter Locations on the Supported Platforms PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-4 Figure 1-5 P ort Adapter Slots in the Cisco 7200 Series—Cisco 7206 Figure 1-6 shows a Cisco uBR7200 series router with port adapters installed.
Overview 1-5 LEDs LEDs The P A-FE-TX and the P A-FE-FX hav e an enabled LED, standard on all port adapters, and a bank of three status LEDs for the ports. After system initialization, the enabled LED goes on to indicate that the P A-FE has been enabled for operation.
Receptacles, Cables, and Pinouts PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-6 Figure 1-8 shows the RJ-45 cable connectors. Cisco Systems does not supply Category 5 UTP RJ-45 cables; these cables are av ailable commercially .
Overview 1-7 Receptacles, Cables, and Pinouts Figure 1-10 Crosso ver Cable Pinout—P A-FE-TX RJ-45 Connections Between Hubs and Repeaters Figure 1-11 shows the duple x SC connector (one required for .
Receptacles, Cables, and Pinouts PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-8 Figure 1-13 P A-FE-TX or P A-FE-FX MII Connection—Receptacle T able 1-2 lists the MII connector pinout and signals. MII cables are av ailable commercially and are not av ailable from Cisco Systems.
Overview 1-9 Fast Ethernet Overview F ast Ethernet Overview The term Ethernet is commonly used for all carrier sense multiple access collision detect (CSMA/CD), LANs that generally conform to Ethernet specifications, including Fast Ethernet under IEEE 802.
IEEE 802.3u 100BaseT Specifications PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-10 IEEE 802.3u 100BaseT Specifications T able 1-3 lists the cabling specifications for 100-Mbps Fast Ethernet transmission over UTP , FTP , and fiber-optic cables.
CHAPTER Preparing for Installation 2-1 2 Prepar ing f or Installation This chapter describes the general equipment, safety , and site preparation requirements for installing the P A-FE-TX and P A-FE-FX Fast Ethernet port adapters.
Software and Hardware Requirements PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 2-2 Software and Har dware Requirements T able 2-1 lists the minimum Cisco IOS software release required to use the P A-FE-TX and P A-FE-FX in supported router platforms.
Preparing for Installation 2-3 Safety Guidelines Caution The VIP2 requires that Cisco 7000 series routers hav e the RSP7000 and RSP7000CI installed. The VIP2 will not operate properly with the Route Processor (RP), Switch Processor (SP), or Silicon Switch Processor (SSP) installed in a Cisco 7000 series router .
Safety Guidelines PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 2-4 La traduzione delle avv ertenze riportate in questa pubblicazione si trov a nel documento Re gulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositiv o.
Preparing for Installation 2-5 Preventing Electrostatic Discharge Damage • Ne ver touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines.
FCC Class B Compliance PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 2-6 FCC Class B Compliance The equipment described in this document generates and may radiate radio-frequency ener gy .
CHAPTER VIP2 and the PA-FE Port Adapters 3-1 3 VIP2 and the P A-FE P or t Adapters This chapter provides information on the P A-FE-TX and the P A-FE-FX port adapters and their use in the VIP2 in Cisco 7000 series and Cisco 7500 series routers.
Installation Overview PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-2 The P A-FE-TX and P A-FE-FX can be installed in either port adapter slot 0 or port adapter slot 1 on the VIP2. Figure 3-1 shows a P A-FE-TX installed in port adapter slot 0 on a VIP2-15 or VIP2-40.
VIP2 and the PA-FE Port Adapters 3-3 Installation Overview Figure 3-2 VIP2-15 or VIP2-40 with a P A-FE-FX in Port Adapter Slot 0 Figure 3-3 shows a P A-FE-TX installed in port adapter slot 0 on a VIP2-50. Figure 3-4 shows a P A-FE-FX installed in port adapter slot 0 on a VIP2-50.
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-4 Figure 3-4 VIP2-50 with an P A-FE-FX in Port Adapter Slot 0 Remo ving a P or t Adap.
VIP2 and the PA-FE Port Adapters 3-5 Removing a Port Adapter Step 4 Locate the scre w at the rear of the port adapter (or blank port adapter) to be replaced.
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-6 Installing a P or t Adapter Use the following standard procedure to install a port adapter on a VIP2: Step 1 Attach an ESD-pre venti ve wrist strap between you and an unfinished chassis surface.
VIP2 and the PA-FE Port Adapters 3-7 Installing a Port Adapter Step 4 Carefully slide the ne w port adapter into the port adapter slot until the connector on the port adapter is completely seated in the connector on the motherboard. Step 5 Replace the scre w in the rear of the port adapter slot.
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-8.
CHAPTER Cisco 7200 Series and the PA-FE Port Adapters 4-1 4 Cisco 7200 Ser ies and the P A-FE P or t Adapters This chapter provides information on the P A-FE-TX and P A-FE-FX port adapters and their use in the Cisco 7200 series routers.
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 4-2 Figure 4-1 Cisco 7206 with a P A-FE-TX in Slot 4 Figure 4-2 shows a Cisco 7206 with a P A-FE-FX installed in slot 4.
Cisco 7200 Series and the PA-FE Port Adapters 4-3 Removing a Port Adapter Figure 4-3 Placing the P ort Adapter Lever in the Unlocked P osition—Cisco 7206 Step 3 Grasp the handle on the port adapter and pull the port adapter from the midplane, about halfway out of its slot.
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 4-4 Installing a P or t Adapter Use the following procedure to install a ne w port adapter in a Cisco 7200 series router: Step 1 Attach an ESD-pre venti ve wrist strap between you and an unfinished chassis surface.
Cisco 7200 Series and the PA-FE Port Adapters 4-5 Installing a Port Adapter Figure 4-6 Placing the P ort Adapter Lever in the Locked P osition—Cisco 7206 This completes the procedure for installing a new port adapter in a Cisco 7200 series router .
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 4-6.
CHAPTER Cisco uBR7200 Series and the PA-FE Port Adapters 5-1 5 Cisco uBR7200 Ser ies and the P A-FE P or t Adapters This chapter provides information on the P A-FE-TX and P A-FE-FX port adapters and their use in Cisco uBR7200 series univ ersal broadband routers.
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 5-2 Figure 5-1 Cisco uBR7200 Series with a P A-FE-TX in Slot 2—Cisco uBR7246 Figure 5-2 shows a P A-FE-FX installed in slot 2 of a Cisco uBR7200 series router .
Cisco uBR7200 Series and the PA-FE Port Adapters 5-3 Removing a Port Adapter Figure 5-3 Placing the P ort Adapter Retention Clip in the Unlocked P osition—Cisco uBR7246 — For a Cisco uBR7223, place the port adapter lev er in the unlocked position.
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 5-4 Caution Always handle the port adapter by the carrier edges and handle; ne ver touch the port adapter’ s components or connector pins.
Cisco uBR7200 Series and the PA-FE Port Adapters 5-5 Installing a Port Adapter Figure 5-6 Aligning the P ort Adapter Metal Carrier Between the Slot Guides Step 4 W ith the metal carrier aligned in the slot guides, gently slide the port adapter halfway into the slot.
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 5-6 Figure 5-7 Placing the P ort Adapter Retention Clip in the Locked P osition—Cisco uBR7246 For a Cisco uBR7223, place the port adapter lev er in the locked position.
CHAPTER Cisco 7100 Series and the PA-FE-TX and PA-FE-FX 6-1 6 Cisco 7100 Ser ies and the P A-FE-TX and P A-FE-FX This chapter provides information on the P A-FE-TX and P A-FE-FX port adapters and their use in Cisco 7100 series routers.
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 6-2 Figure 6-2 Cisco 7140 series Router—P ort Adapter Slot 4 Location Depending on your circumstances, you might need to install a new port adapter in a Cisco 7100 series router or replace a failed port adapter in the field.
Cisco 7100 Series and the PA-FE-TX and PA-FE-FX 6-3 Installing a Port Adapter Caution Always handle the port adapter by the carrier edges and handle; ne ver touch the port adapter’ s components or connector pins.
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 6-4 Caution Do not slide the port adapter all the way into the slot until you hav e connected all required cables. T rying to do so disrupts normal operation of the router .
CHAPTER Installing PA-FE Port Adapter Interface Cables 7-1 7 Installing P A-FE P or t Adapter Interf ace Cab les T o continue your P A-FE-TX and P A-FE-FX port adapter installation, you must install the port adapter’ s interface cables. The following instructions apply to all supported platforms.
Attaching PA-FE Port Adapter Interface Cables PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 7-2 Note Each P A-FE-FX or P A-FE-TX can hav e either an MII attachment or an RJ-45 (or SC) attachment, but not both simultaneously .
Installing PA-FE Port Adapter Interface Cables 7-3 Attaching PA-FE Port Adapter Interface Cables Step 2 For the P A-FE-TX, attach the ferrite bead to the RJ-45 cable (at either end), as shown in Figure 7-3.
Attaching PA-FE Port Adapter Interface Cables PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 7-4.
CHAPTER Configuring PA-FE Port Adapter Interfaces 8-1 8 Configur ing P A-FE P or t Adapter Interf aces T o continue your P A-FE-TX and P A-FE-FX port adapter installation, you must configure the P A-FE-TX and P A-FE-FX interfaces. The follo wing instructions apply to all supported platforms.
Using the EXEC Command Interpreter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-2 Using the EXEC Command Interpreter Y ou modify the configuration of your router through the software command interpreter called the EXEC.
Configuring PA-FE Port Adapter Interfaces 8-3 Note For the Cisco 7206VXR and Cisco 7206 router shelves, physical port addresses are composed of a three-part number in the format shelf number/port adap.
Identifying Chassis Slot, Port Adapter Slot, and PA-FE Interface Port Numbers PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-4 The indi vidual interface port numbers always be gin with 0. The number of additional ports depends on the number of ports on a port adapter .
Configuring PA-FE Port Adapter Interfaces 8-5 Note Although the processor slots in the sev en-slot Cisco 7000 and Cisco 7507 and thirteen-slot Cisco 7513 are vertically oriented and those in the fi ve-slot Cisco 7010 and Cisco 7505 are horizontally oriented, all models use the same method for slot and port numbering.
Performing a Basic Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-6 Figure 8-4 P ort Adapter Slot Numbering—Cisco 7120 Series Slots in the Cisco 7140 series are numbered as shown Figure 8-5.
Configuring PA-FE Port Adapter Interfaces 8-7 Use the following sample basic configuration procedure: Step 1 At the pri vileged-le vel prompt, enter configuration mode and specify that the console terminal is the source of the configuration subcommands, as follows: Router# configure terminal Enter configuration commands, one per line.
Performing a Basic Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-8 Configuring P A-FE T ransmission Mode Half-duplex operation is the def ault transmission mode for the P A-FE.
Configuring PA-FE Port Adapter Interfaces 8-9 T o check the interface configuration using show commands, proceed to the “Checking the Configuration” section on page 8-9.
Checking the Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-10 If the interface is do wn and you configured it as up, or if the displays indicate that the hardware is not functioning properly , ensure that the network interface is properly connected and terminated.
Configuring PA-FE Port Adapter Interfaces 8-11 cisco 7200 (R4700) processor with 22528K/10240K bytes of memory. R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache) Last reset from power-on Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
Checking the Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-12 VIP2 Show Commands Use the show interfaces type slot/port-adapter/por t command.
Configuring PA-FE Port Adapter Interfaces 8-13 Use the show diagb us slot command to determine which type of port adapter is installed on a VIP2 in your system.
Checking the Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-14 Follo wing is an example of a successful ping command to a remote server with the address 172.16.0.0: Router# ping 172.16.0.0 Type escape sequence to abort.
An important point after buying a device Cisco Systems PA-FE-TX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems PA-FE-TX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems PA-FE-TX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems PA-FE-TX you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems PA-FE-TX will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems PA-FE-TX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems PA-FE-TX.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems PA-FE-TX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems PA-FE-TX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
