Instruction/ maintenance manual of the product OL-23421-02 Cisco Systems
Go to page of 46
Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco we bsite at www.
THE SPECIFICATION S AND INFORMAT ION REGARDING THE PRODUCTS IN THIS MA NUAL ARE SUBJ ECT TO CHANGE WITHOUT NOT ICE. ALL STATEMENTS , INFORMATION, AND RECOMMEN DATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESEN TED WITHOU T WARRANTY OF ANY KIND, EX PRESS OR IMPLIED.
1 Cisco Connected Grid Ethernet Switch Modul e Inte rface Card Getting Started Guide OL-23421-02 CONTENTS Preface iii Purpose iii Document Conventions iii Related Publication s iv Obtaining Documentat.
Contents 2 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Troubleshooting Express Setup 3-5 Resetting the Switch Module 3-5 CHAPTER 4 Managing the Switc.
iii Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Preface Purpose This guide describes the hardwa re features of th e Cisco Connected Grid Ethernet Swi tch Module Interface Card (swi tch module).
iv Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Related Publications Note Before installing, conf iguring, or upgrading the switch, see the release not es on Cisco.
CH A P T E R 1-1 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 1 Product Overview This chapter describes the Cisco Connected Grid Et hernet Switch Module Interface Card, hereafter referred to as the switch module.
1-2 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 1 Product Overview Ports Ports • Port Locations, page 1-2 • Port Labeling, page 1-3 • 1.
1-3 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 1 Product Over view Ports Figur e 1 -2 GRWIC-D-ES-2S-8PC (Copper Model) Port Labeling The port labeling for the switc h modules is described in Ta b l e 1 - 2 and T able 1-3 .
1-4 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 1 Product Overview Ports 10/100BASE-T Ports Y ou can set the 10/100B A SE-T ports on the switch to operate in an y combination of half duple x , full duple x, or 10 or 100 Mb/s.
1-5 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 1 Product Overview Ports – power r eservat ion – per -port po wer policing On the GR WIC-D-ES-2S-8PC model (Copper model), the f irst four 10/100B ASE-T ports (FE0/1, FE0/2, FE0/3, FE0/4) ar e PoE+ ports.
1-6 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 1 Product Overview Ports Supported SFPs T able 1-4 descri bes the supported SFP modules.
1-7 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 1 Product Overview LEDs LEDs This section descri bes the location and functi on of the LEDs on the switch module.
1-8 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 1 Product Overview LEDs Figur e 1 -4 GRWIC-D-ES-2S-8PC S witch Module (Copper Model) LEDs GE0/1 Indicates the state of the Gig abit Ethernet dual pur pose port: • LED is flashing green—data transmission is taking place.
1-9 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 1 Product Overview Router Compa ct Flash Memory Cards Router Compact Flash Memory Cards Compact flash cards can help you conf igure new or re placemen t routers, and to recov er the configuration of a fail ed router .
1-10 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 1 Product Overview Router Compact Flash Memory Cards For more information on the Swap Dri ve feature, see: http://www .cisco .com/en/US/ docs/routers/ connec tedgrid/cgr2010/softw are/15_2_2_t/cgr2010_15_2_2 _t_swcg.
CH A P T E R 2-1 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 2 Installation This section describes ho w to install the switch modu le in C isco CGR 201 0 rout ers. The switch module occupies two of four slo ts on the I/O side of the rou ter .
2-2 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 2 Installation Installation War ni n g This unit is intend ed for installation in restricted access are as. A restricted access area can be accessed only through the use of a special too l, lock and key , or other means of security .
2-3 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 2 Installation Installation Figure 2-1 Removing the Slot Divider F rom the CGR 20 1 0 Router Step 3 Stand the switch module on end to install i t into the Cisco CGR 2010 router slot (see Figure 2-2 ).
2-4 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 2 Installation Installation Step 4 Grasp the handles and carefully slide the mod ule into the card guid e, then push with bo th hands until the module is flush against the router chassis (see Figure 2-3 ).
2-5 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 2 Installation Connecting to the Network Figure 2-4 S wi tch Module Installed in the CGR 20.
2-6 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 2 Installation Connecting to the Network Figure 2-5 Connecting the Copper Model to the Netw or k Step 2 Connect the other end of the cabl e to th e RJ-45 connector of the target device.
2-7 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 2 Installation Removing the Switch Module Figur e 2-6 Connecting the SFP Fiber Model t o the Netw or k Step 2 Connect the other end of the cabl e to the standard LC-type optical connector on the tar get devi ce.
2-8 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 2 Installation Removing the Switch Module.
CH A P T E R 3-1 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 3 Express Setup Y o u access the switch module via the host CGR 2010 router . For more information , see Accessing the Switch Module, pa ge 4-2 .
3-2 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 3 Express Setup Express Setup Step 2 V erify that no de vice is conn ec ted to the switch module. Step 3 T emporarily confi gure your computer to use DHCP , if it has a static IP address.
3-3 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 3 Express Setup Express Setup Step 6 Select one of the following: • For th e Copper Model.
3-4 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 3 Express Setup Express Setup Step 3 Enter the Ne twork Se ttings values: Step 4 Enter the Optional Set tings no w , or enter th em later using the Device Manager interf ace.
3-5 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 3 Express Setup Troubleshooting Express Setup • Confir m that the computer that you are using to access the switch modu le has network connecti vity by connectin g to a web server in your network.
3-6 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 3 Express Setup Resetting the Switch Module Step 2 Press the Express Setup b utton again for three seconds. The switch module 10/1 00 Ethernet port LED blinks green.
CH A P T E R 4-1 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 4 Managing the Switch Module After completing Express Setup and in stalling the switch.
4-2 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 4 Mana ging the Switch Module Other Management Options Note Y ou must be a regist ered Cisco.com user , but you need no other access pri vileges.
4-3 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 4 Managing the Switch Module Accessing the Switch Module The service-module gigabi tEthernet 0/x /0 session command is the pri vileged EXEC mode comman d used to console into th e Ethernet switch modul e from the host rou ter .
4-4 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 4 Mana ging the Switch Module Connecting Devices to the Switch Module Connecting Devices to the Switch Module This section descri bes ho w to connect v arious devi ces to the switch module por ts.
4-5 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 4 Managing the Switch Module Connecting Devices to the Switch Module Figure 4-1 RJ-45 P orts Step 2 Connect the cable to the RJ-45 port on the other device.
4-6 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 4 Mana ging the Switch Module Connecting Devices to the Switch Module Figur e 4-2 SFP Module P orts Step 2 Connect the SFP cable into the SFP mo dule slot, and inser t the other cable end into the other device.
4-7 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 4 Managing the Switch Module Connecting Devices to the Switch Module For detailed instructions on inst al ling, removing, and co nnect ing to SFP module s, see the SFP module documentation.
4-8 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 4 Mana ging the Switch Module Connecting Devices to the Switch Module Figure 4-4 Ether net Cable Connected to the RJ-45 Connecto r Figure 4-5 sho ws both connectors of the dual-purp o se port being used.
4-9 Cisco Connected Grid Eth ernet Switch Modu le Interface Card Ge tting Started Guid e OL-23421-02 Chapter 4 Managing the Switch Module Connecting Devices to the Switch Module Figur e 4-5 Dual-Pur p.
4-10 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Chapter 4 Mana ging the Switch Module Connecting Devices to the Switch Module.
A-1 Cisco Connected Grid Ethernet Sw itch Mo dule Inte rface Card Getting Started Guide OL-23421-02 APPENDIX A Cable and Connectors • Connector Specif ications, page A-1 • Cables and Adap ters, pa.
A-2 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Appendix A Cable and Connectors Cables and Adapters Figure A -2 Fiber -Optic SFP Mo dule LC Connector War ni n g Invisible laser radiation may be emitted from disconnect ed fibers or connectors.
A-3 Cisco Connected Grid Ethernet Switch Modul e Inte rface Card Getting Started Guide OL-23421-02 Appendix A Cable and Connectors Cables and Adapters T able A -1 Fiber -Optic SFP Module P ort Cabling.
A-4 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Appendix A Cable and Connectors Cables and Adapters Note When the fiber -optic cable span is less than 15.
A-5 Cisco Connected Grid Ethernet Switch Modul e Inte rface Card Getting Started Guide OL-23421-02 Appendix A Cable and Connectors Cables and Adapters Figur e A -6 F our T wisted-P a ir Straight-T hr .
A-6 Cisco Connected Grid Ethern et Switch Module Interface Card Getting Started Gu ide OL-23421-02 Appendix A Cable and Connectors Cables and Adapters.
An important point after buying a device Cisco Systems OL-23421-02 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems OL-23421-02 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems OL-23421-02 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems OL-23421-02 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems OL-23421-02 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems OL-23421-02, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems OL-23421-02.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems OL-23421-02. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems OL-23421-02 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
