Instruction/ maintenance manual of the product ATA 186 Cisco Systems
Go to page of 14
Configuring and Troubleshooting an ATA 186 with Cisco IOS Gatekeepers Document ID: 19084 Introduction Prerequisites Requirements Components Used Conventions Network Diagram Registering the ATA 186 with the Gatekeeper Adding Security Authenticate the Endpoint at the Gatekeeper with an H.
Components Used The information in this document is based on these software and hardware versions: ATA 186 with version 2.12 • Cisco 3640 with Cisco IOS® Software Release 12.
IP addressing can be done statically or dynamically, as explained in the Cisco ATA 186 Basic Configuration document. In the previous screen, the static IP address is used. In the Cisco ATA 186 Configuration window, configure these fields: UID0 and UID1Configure the E.
GKOrProxyConfigure the IP address of the gatekeeper. Once this is done, anything that is dialed from the ATA 186 voice ports is sent to the gatekeeper. ♦ Click the Apply button and then reload the page. The ATA 186 takes 10 seconds to reconfigure itself.
destination−pattern 300. session target ras !−−− Dial−peer to send the calls to ATA. ! Adding Security As of ATA software release 2.12, the options in this section are available to add security. Authenticate the Endpoint at the Gatekeeper with an H.
aaa authentication login h323 local aaa session−id common enable password ww ! username atagw1 !−−− Same as the LoginID0 and LoginID1 fields. username atagw2 username 3640 !−−− Same as the H.323 ID configured on the gateway. ! gatekeeper zone local gk2 cisco.
Authenticate the Endpoint at the Gatekeeper with an H.323 ID and Password Follow these steps to configure the ATA 186 to register with the H.323 ID and password: Set the AutMethod field to 1 (the default is 1). The hexadecimal value that is to be configured for this field is 0x1.
Authenticate the Endpoint at the Gatekeeper with an E.164 Address and Password Follow these steps to configure the ATA 186 to register with the E.164 ID and password: Set the AutMethod field to 1 (the default is 1). The hexadecimal value that is to be configured for this field is 0x0.
Authenticate the Endpoint at the Gatekeeper with an H.323 ID and Password Using the Separator Follow these steps to configure the ATA 186 to register with the H.323 ID and password: Set the AutMethod field to 1 (the default is 1). The hexadecimal value configured for this field is 0x1.
Verify The example in this section shows the gatekeeper endpoint registration. To verify the configuration, issue the show gatekeeper endpoint command.
Note: The ATA 186 registers for the two voice ports separately. The ATA 186, therefore, gets authenticated twice as different H.323 terminals, as shown in this debug: 4w4d: AAA/AUTHEN/CONT (3800768902.
GK−>1: RCF:TTL 300 GK−>0: RCF:TTL 300 SCC−>(0 0) <cmd 0> 3000 active @0xab45555a (GK @0xac100d0c) !−−− Call made from voice port 0.
write TCP err : 13 −33 [0:0]Rel LBRC Res Q931<−*:ReleaseComplete !−−− ATA side hangs up the call. write TCP err : 12 −33 GK<−0: DRQ:0 !−−− Disconnect request sent by ATA. SCC:ev=13[0:0] 4 0 [0:0]SCC: Disconnected GK−>0: DCF !−−− Disconnect confirm received.
Configuring Voice over IP • Voice Technology Support • Voice and IP Communications Product Support • Recommended Reading: Troubleshooting Cisco IP Telephony • Technical Support & Documentation − Cisco Systems • All contents are Copyright © 2006−2007 Cisco Systems, Inc.
An important point after buying a device Cisco Systems ATA 186 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems ATA 186 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems ATA 186 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems ATA 186 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems ATA 186 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems ATA 186, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems ATA 186.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems ATA 186. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems ATA 186 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
