Instruction/ maintenance manual of the product 3.1(6) Cisco Systems
Go to page of 17
Cisco Unity 3.1(6) Installation Guide: Installing a Windows 2000 Server for Component System Document ID: 44332 Introduction Prerequisites Requirements Components Used Conventions Task 1: Start the Wi.
and hardware components must be installed by the installer of the Cisco Unity system. The Cisco Unity software package is purchased from Cisco or from a Cisco reseller.
Requirements Before you attempt this configuration, ensure that you meet these requirements: Windows 2000 Server Administration. • IP Addressing and related TCP/IP configuration options such as DNS, gateways, and so forth. • Components Used The information in this document is based on these software and hardware versions: Cisco Unity 3.
When the text "Setup will load support..." appears, press Enter . Note: If you see a message that indicates the installation cannot continue because a hard disk could not be detected, it is possible that you have not used the correct third party Windows 2000 Server driver.
Caution: If you elect to install an option that is listed as [No] below and it causes a conflict with Cisco Unity, you need to unconfigure it. It might not be supported on a server that runs Cisco Unity.
If the server that you are configuring is going to run Active Directory, you must enable File and Print Sharing For Microsoft Networks . This is required because Active Directory uses Networking in order to share the Active Directory files.
Select the Add/Remove Windows Components option. A menu screen similar to this image appears. 3. Select the Configure Message Queueing Services (Configure) option. Follow the prompts in order to complete the installation of Message Queueing Services. There are no user configurable options for this task.
Select Finish when the installation is completed. Close all of the Windows that are currently open. 5. Log off the current session and log back on again. The Windows 2000 Configure Your Server menu screen similar to this image appears. 6. Select the I will configure this server later option and select Next .
Un−select the Show this screen at startup option. Then close this window. 8. Task 4: Install Additional Windows 2000 Languages (Optional) If you want to view the Windows user interface in languages other than English, install the applicable languages.
Pack 2. Caution: When you install Internet Explorer, the file WScript.exe is installed automatically. Do not remove WScript.exe, or the Cisco Unity Setup program fails. Insert the Internet Explorer 5.5 CD that came with your Cisco Unity CD set in the CD−ROM drive.
Task 9: Change Windows Explorer Settings (Optional) This procedure ensures that all system files and folders are visible in Windows Explorer. This facilitates troubleshooting system problems in the future. From the Windows desktop, double−click My Computer .
tracert command instead. c:>tracert ip_address You should see a response something like this: Tracing route to [x.x.x.x] over a maximum of 30 hops: 1 <10ms <10ms <10ms [y.y.y.y] Where y.y.y.y is the IP address of the first gateway between your server and the IP address that you used.
Browse to the Bootdisk directory. 3. Double−click Makebt32.exe . 4. Follow the on−screen prompts. 5. Go to step 1 in Task 1. 6. Appendix B: Configure the Most Common TCP/IP Parameters Complete this procedure in order to configure the most common TCP/IP parameters.
A menu window similar to this image appears. Configure the IP options as appropriate. If you will be running Active Directory and DNS on this server, it should have itself as the first DNS Server. Select the Advanced option. A menu window similar to this image appears.
Click the DNS tab. A menu window similar to this image appears. 4..
These settings are correct for most systems. Consult your Windows 2000 Server documentation if you need more information on the configuration of TCP/IP options. Appendix C: Change the Name of the Computer Name (Optional) If you plan to change the name of your computer, do it as soon as possible.
NetPro Discussion Forums − Featured Conversations Networking Professionals Connection is a forum for networking professionals to share questions, suggestions, and information about networking solutions, products, and technologies. The featured links are some of the most recent conversations available in this technology.
An important point after buying a device Cisco Systems 3.1(6) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems 3.1(6) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems 3.1(6) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems 3.1(6) you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems 3.1(6) will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems 3.1(6), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems 3.1(6).
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems 3.1(6). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems 3.1(6) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
