Instruction/ maintenance manual of the product Network Switch Cabling Cisco
Go to page of 18
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 16 Control Node and Network Switch Cabling Example This docume nt provides background infor mation and detailed procedures for cab ling dual Cassatt Active R esponse control nodes a nd netw o rk switches and for configuring those netw ork switches .
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 17 application nodes . Note that detailed instr uct ions for adding application nodes are in a separate documen t, which yo u should consult wh en you are ready to cable application nodes into your Cassatt Acti ve R esp onse environment.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 18 T able 1 shows ho w each por t is used on the switc h and control node . T able 1 Description of Panel and Main Board Not ation Not a tion Description ISL-1 Used to create the first half of interswitch link (ISL) connection between the tw o Cisco switches .
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 19 Racking and cabling guidelines T o cable your control nodes to the network sw itc hes according to Figure 1, follow these steps .
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 20 3. Connect the cont rol nodes to the shared sto rage hardware, as follows: 4. Using crossov er cables , create an inters witch link (ISL) betw een the two Cisco 3750 switches .
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 21 Configuring the switches After you hav e racked and cabled the control nodes and sw itches , you need to configure both Cisco switch stac ks .
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 22 4. Plug in the Cisco switches in a stac k. 5. Many boot-up and self-test messages will scroll on the console monitor .
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 23 3. If the switch w a s used previously in a switch stack, and is no w in a diff erent switch stack, it may ha ve a switch n umber other than 1 and 2.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 24 Changing Switch Number 3 to Switch Number 2 New Switch Number will be effective after next reboot 6.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 25 2. Enter the privileged mode, as follows: 3. Enter the configuration mode, as follo ws: Enter configuration commands, one per line. End with CNTL/Z. 4. T urn the messag es off, as follows: 5.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 26 7. Set the host name of the switc h stack, as follo ws: 8. Set the switch stac k’ s enable password, as follo ws: 9. T ur n off the VLAN tr unking protoc ol (VTP), as follows: sw01(config)# Setting device to VTP TRANSPARENT mode.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 27 11. Ag g reg ate the tw o physical links betw een the two Cisco switches in the stac k into a single logical link, as follows: Creating a port-channel interface Port-channel 1 12.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 28 13. Set the remaining interfaces , wh ich are identical, as follo ws . %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 29 %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode 14. Disable IGMP snooping, as follows: 15.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 30 17. T ur n all the interfaces back on, as follo ws: 18. T ur n log ging to the c onsole back on, as follows: 19. Exit the configuration mode, as follo ws: 20. V erify the switch configuration, as follo ws: Building configuration.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 31 interface Port-channel1 no ip address ! interface GigabitEthernet1/0/1 no ip address no mdix auto channel-group 1 mo.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 32 ! interface GigabitEthernet2/0/3 switchport mode access no ip address no mdix auto spanning-tree portfast ! interfac.
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 33 21. Sav e the configuration across a reboot of the switch, as follows: Destination filename [startup-config]? Building configuration.
An important point after buying a device Cisco Network Switch Cabling (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Network Switch Cabling yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Network Switch Cabling - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Network Switch Cabling you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Network Switch Cabling will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Network Switch Cabling, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Network Switch Cabling.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Network Switch Cabling. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Network Switch Cabling along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
