Instruction/ maintenance manual of the product LightStream 100 Cisco
Go to page of 10
CHAPTER Preparing for Installation 2-1 Prepar ing f or Installation 2 This chapter provides safety information and describes the tasks you must perform before you install the LightStream 100 A TM switch.
2-2 Cisco LightStream 100 User Guide Safety Recommendations W arning Class 1 laser product. T o see this warning in multiple languages, refer to the “Class 1 Laser Product W arning” section in the “T ranslated Safety W arnings” appendix. W arning Do not stare into the beam or view it directly with optical instruments.
Preparing for Installation 2-3 Safety Recommendations • Look carefully for possible hazards in your work area, such as moist floors, ungrounded po wer extension cables, and missing safety grounds. • If an electrical accident occurs, proceed as follows: — Use caution; do not become a victim yourself.
2-4 Cisco LightStream 100 User Guide Installation Environmental Conditions Installation En vironmental Conditions Install the LightStream 100 A TM switch in an area that meets the following conditions: 1 Make sure the LightStream 100 switch remains operational within the temperature and humidity limits sho wn in T able 1-3.
Preparing for Installation 2-5 LightStream 100 ATM Switch Components • Center card (P-8X55-A) • Processor (PR OC) card (FSB3523GX, P-8X0R) • Gate way Packet Assembler/Disassembler (GWP AD) card .
2-6 Cisco LightStream 100 User Guide LightStream 100 ATM Switch Components Figure 2-1 LightStream 100 A TM Switch Fr ont Panel H2410 Ethernet connection EIA/TIA-232 Operator LEDs (16) Reset button Run.
Preparing for Installation 2-7 LightStream 100 ATM Switch Components Figure 2-2 LightStream 100 A TM Switch Rear P anel AC power connector H2411 Cooling fans Power switch.
2-8 Cisco LightStream 100 User Guide LightStream 100 ATM Switch Components Figure 2-3 LightStream 100 A TM Switch Internal View Fa n BCONV : Bus Conv er ter GWP AD : Gatew ay P ack et Assembler/Disass.
Preparing for Installation 2-9 LightStream 100 ATM Switch Components Figure 2-4 Expanded Internal View (Motherboar d) CLKGEN Motherboard A TOM SW : Asynchronous T ransfer Mode Output-Buff er Modular S.
2-10 Cisco LightStream 100 User Guide LightStream 100 ATM Switch Components.
An important point after buying a device Cisco LightStream 100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco LightStream 100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco LightStream 100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco LightStream 100 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco LightStream 100 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco LightStream 100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco LightStream 100.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco LightStream 100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco LightStream 100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
