Instruction/ maintenance manual of the product 7000 Cisco
Go to page of 38
1 Doc. No . Copyright © 1995 Cisco Systems, Inc. All rights reser ved. Cisco 7000 and Cisco 7507 Rac k-Mount Kit Installation Instructions 78-1058-03 Product Number s: EFT -RMK, A CS-7KRMK and A CS-7.
2 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions Rack-Mount Kit Overview Rack-Mount Kit Overvie w This section describes the types of racks for which this rack-mounting kit is intended, and the mounting configurations that are possible with each type.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 3 Rack-Mount Kit Overview Rack-Mount Installation Summary Follo wing is a summary of the installation procedures required to rack-mount the chassis. This summary is informational and is not intended to replace the actual procedures required to rack-mount the chassis.
4 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions Rack-Mount Kit Overview Figure 2 shows the components in this mounting kit. Figure 2 Rack-Mount Kit Components Each of the chassis ears attaches to a side of the chassis with two M4 x 10-mm, Phillips, flat-head scre ws).
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 5 Rack-Mount Kit Overview In T elco-type installations, you can install the chassis so that the ends of the chassis are approximately centered on two posts. Figure 3 shows a typical center -mount installation.
6 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions Rack-Mount Kit Overview Figure 4 shows a typical flush-mount installation. Figure 4 T ypical Flush-Mount Installation—For T elco.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 7 Prerequisites Prerequisites Before you begin this installation, re vie w the safety guidelines in this section to av oid injuring yourself or damaging the equipment.
8 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions Prerequisites Saf ety Guidelines Revie w the following guidelines to help ensure your safety and protect the equipment from damage during the installation. W arning Before working on a system that has an on/of f switch, turn OFF the po wer and unplug the po wer cord.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 9 Prerequisites • Ensure that your footing is solid and balance the weight of the object between your feet. • Lift the object slowly; ne ver move suddenly or twist your body as you lift.
10 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Prerequisites Saf ety with Electricity Follo w these basic guidelines when working with an y electrical equipment: • Before beginning an y procedures requiring access to the chassis interior , locate the emergenc y po wer-of f switch for the room in which you are working.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 11 Prerequisites When you replace the po wer supplies, remember to engage all of the safety features on each supply .
12 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Prerequisites Rack Stability When installing the chassis in any rack that is not secured to the floor or o verhead structure, place the chassis in the lower half of the rack. A fully-configured chassis weighs 145 pounds (65.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 13 Prerequisites Also, when installing the chassis in T elco-type racks, ensure that the rack is secured to the floor or otherwise stabilized. Center-mount the chassis if possible (and practical for your installation).
14 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Prerequisites Rack Dimensions and Site La yout For complete site requirements and recommendations, refer to the Cisco 7000 Hardwar e Installation and Maintenance or Cisco 7507 Hardwar e Installation and Maintenance publications.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 15 Prerequisites List of P ar ts and T ools This section lists the tools you will need to complete this installation and the parts that are shipped as part of the rack-mount kit.
16 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Installation Installation The following sections describe the procedures for mounting the chassis in a 19-inch equipment rack with two or four mounting posts.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 17 Installation After you install both brackets in the rack, you must connect the spanner bar on each bracket to the opposite bracket. The spanner bars are required to pre vent both ends of the brack ets (at the front and rear of the rack) from separating or drifting apart.
18 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Installation Step 4 Slide the bracket up and do wn along the mounting post to align the mounting holes in the bracket with those in the rack post.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 19 Installation Figure 11 P ositioning and Fastening a Spanner Bar Caution T o ensure adequate space between the brackets and a proper chassis fit, push the brack ets as far apart as possible before tightening the scre ws that secure them and the spanner bars.
20 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Installation Attaching the Chassis Ears The ears attach directly to the chassis with four M4 x 10-mm, flat-head screws. Attach the ears to the chassis before you slide the chassis onto the brackets and back into the rack.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 21 Installation Follo w these steps to install the ears on the chassis: Step 1 While referring to Figure 12, position the ears on the.
22 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Installation Step 6 If a second po wer supply is installed, repeat steps Steps 3 through 5 to remove the second supply .
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 23 Installation Figure 14 Chassis Foot If you hav e not already done so, re view the safety guidelines in the section “Lifting the Chassis Safely” on page 8. Then follow these steps to install the chassis in the rack: Step 1 T wo people ar e r equir ed to perform this step.
24 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Installation Figure 15 Sliding the Chassis into the Rack Checking Electrical Isolation The inner sides of the mounting brackets and the grommets on the chassis ears are shielded to isolate the chassis from contact with the equipment rack.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 25 Installation Replacing P ower Supplies and Interf ace Cables Before proceeding, ensure that you hav e suf ficient working space (.
26 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Installation Restar ting the System T o complete the installation, you will perform a final check of all connections, then restart the system.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 27 Installation Figure 16 Cisco 7000 P ort Configuration W orksheet Circle one: AIP/CIP/EIP/FIP/ FSIP/HIP/TRIP 0/0 0/1 0/2 0/3 0/4 0.
28 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Installation Figure 17 Cisco 7507 P ort Configuration W orksheet Circle one: AIP/CIP/EIP/FEIP/FIP/ FSIP/HIP/TRIP/MIP 0/0 0/1 0/2.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 29 Translated Safety Warnings T ranslated Safety W arnings Follo wing are translations of the safety warnings that appear throughout .
30 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions T ranslated Safety W arnings V aroitus Älä kosketa virtalähdettä virtajohdon ollessa k ytkettynä.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 31 Translated Safety Warnings Attention A v ant de trav ailler sur un châssis ou à proximité d'une alimentation électrique, .
32 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions T ranslated Safety W arnings ¡Advertencia! Puede ser que este equipo posea más de un cable de alimentación. Para reducir el riesgo de descarga eléctrica, desenchuf ar los dos cables antes de proceder al mantenimiento de la unidad.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 33 Translated Safety Warnings Adv arsel Det er nødv endig med to personer for å løfte kabinettet. T a tak i kabinettet under den nedre kanten, og løft med begge hender . Unngå personskade ved å holde ryggen rett og løfte med bena, ikke ryggen.
34 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions T ranslated Safety W arnings A vvertenza Prima di svolgere una qualsiasi delle procedure seguenti, v erificare che il circuito CC non sia alimentato.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 35 Translated Safety Warnings Chassis W arning—Rack-Mounting and Servicing W arning T o pre vent bodily injury when mounting or servicing this unit in a rack, you must tak e special precautions to ensure that the system remains stable.
36 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions T ranslated Safety W arnings W arnung Zur V ermeidung von Körperverletzung beim Anbringen oder W arten dieser Einheit in einem Gestell müssen Sie besondere V orkehrungen treffen, um sicherzustellen, daß das System stabil bleibt.
Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 37 Translated Safety Warnings V arning! För att undvika kroppsskada när du installerar eller utför underhållsarbete på denna enhet på en ställning måste du vidta särskilda försiktighetsåtgärder för att försäkra dig om att systemet står stadigt.
38 Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instr uctions Cisco Information Online Cisco Inf ormation Online Cisco Information Online (CIO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CIO to obtain additional content and services.
An important point after buying a device Cisco Cisco 7000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Cisco 7000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Cisco 7000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Cisco 7000 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Cisco 7000 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Cisco 7000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Cisco 7000.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Cisco 7000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Cisco 7000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
