Instruction/ maintenance manual of the product Blower Module 10000 ESR Cisco
Go to page of 22
Corporate Headqu arters: Cisco Systems, Inc., 170 We st Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 20 0 0. Cisco Systems, Inc. All rights reserved.
Product Description 2 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Product Description The A C PEM provides po wer con version directly fro m the facility V A C input po wer (100 V A C to 240 V A C) to the –48V VDC used internally b y the system (see Figure 1).
3 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Prerequisites and Preparation Prerequisites and Preparation Before you perform an y of the p rocedures in this guide, Cisco recommend .
Installation Guidelines 4 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 War ni ng This warning symbo l means danger . Y ou are in a situation that could cause bodily inju ry .
5 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Adding or Replacing an AC PEM This section describes how to add or replace an A C PEM in the Cisco 10000 chassis.
Adding or Replacing an A C PEM 6 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Remov e the cov er by li fting it up sli ghtly and then pulling it t o ward you (Figure 3).
7 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Installing a Second AC PEM Use the follo wing procedure to install a second A C PEM in the bottom po wer bay for redundanc y .
Adding or Replacing an A C PEM 8 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Loosen the capti v e scre ws to remov e the blank co v er from the bottom po wer bay (Figure 5).
9 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 3 Install the ne w AC PEM all t he way into the po wer bay to ensure a secure connection to the backplane, and then tighten the captive scre ws (Figure 6 ).
Adding or Replacing an A C PEM 10 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 4 Connect the po wer cord from the PEM to your po wer cord that connects to th e faci lity V A C input. Step 5 Set the A C power cord connec tors in a cord st rain relief (canoe) to pre vent them from accidently di sconnecting (Figu re 7).
11 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 7 Set the po wer switch to the on (|) positi on (Figure 8). The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 8 Setting the A C P ow er S witch t o the On P osition Step 8 Replace the front cover .
Adding or Replacing an A C PEM 12 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Replacing an AC PEM Use the following procedure to replace an A C PEM. Note The illustrations in this guide sho w how to replace the A C PEM from the bottom po wer bay .
13 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 2 Po wer of f the PEM you are replacing (Figure 10). Caution Do not po wer off both A C PEMs in a redundant system or the system shuts do wn and all data traff ic stops.
Adding or Replacing an A C PEM 14 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 3 Remov e the PEM power cable from its can o e and disconnect it from the A C input po wer cable (Figure 11).
15 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 4 Loosen the captiv e scre ws on the PEM and remo ve the PEM from the chassis using the handle on the faceplate (Figure 12).
Adding or Replacing an A C PEM 16 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 5 Install the ne w PEM all the way into the po wer bay to ensure a good connection to the backplane, and tighten the ca ptiv e scre ws on the PEM (Figure 13).
17 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 6 Connect the po wer cord from the PEM to the po wer cord that connects to the faci lity V A C input. Step 7 Set the A C power cord connec tors in a cord st rain relief (canoe) to pre vent them from accidentl y disconnecting ( Figure 14).
Adding or Replacing an A C PEM 18 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 9 Set the po wer switch to the on (|) positi on (Figure 15) . The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 15 Set ting the A C P ow er Switc h t o the On P osition Step 10 Replace the front cover .
19 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Troubleshooting the Installation T able 1 contai ns troubleshooting i nformation for th e A C PEM: T ab.
FCC Class A Compliance 20 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 FCC Class A Compliance This equipment has been tested and found to comply wi th the limits for a Class A digital de vice, pursuant to part 15 of the FCC rules.
21 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Cisco Connection Online A vail able 24 hours a day , 7 days a week , CCO pro vides a wealth of standard and v alue-added services to Ci sco customers and b usiness partners.
Documentation CD-ROM 22 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Documentation CD-ROM Cisco documentation and add itional lite rature are a vailable in a CD-R OM package, which ships with your p roduct. The Documentation CD-R OM, a member of the Cisco Connectio n Family , is updated mon thly .
An important point after buying a device Cisco Blower Module Cisco 10000 ESR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Blower Module Cisco 10000 ESR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Blower Module Cisco 10000 ESR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Blower Module Cisco 10000 ESR you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Blower Module Cisco 10000 ESR will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Blower Module Cisco 10000 ESR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Blower Module Cisco 10000 ESR.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Blower Module Cisco 10000 ESR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Blower Module Cisco 10000 ESR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
