Instruction/ maintenance manual of the product 2500 Series Cisco
Go to page of 12
1 Doc. No . Cisco Systems, Inc. All rights reser ved. 170 West Tasman Drive San Jose, CA 95134-1706 USA Cisco Systems, Inc. Corporate Headquarters Copyright © 1997 Installing Cisco A C and DC P o wer.
2 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Series Routers Required T ools and Equipment W arning Read the installation instructions before you connect the system to its power source. (T o see translated versions of this warning, refer to the Re gulatory Compliance and Safety Information document that accompanied the router .
Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 3 Removing AC and DC Power Supplies W arning Do not touch the power supply when the power cord is connected. F or systems with a power switch, line v oltages are present within the po wer supply ev en when the power switch is OFF and the po wer cord is connected.
4 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Removing A C and DC P ower Supplies Figure 2 Removing the Scre w Step 2 Disconnect the po wer connector from the system board. (See Figure 3.) Grasp the sides of the power connector and pull upw ard while rocking the connector side to side.
Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 5 Installing AC and DC Power Supplies Figure 4 Removing the P ower Supply Step 4 Place the remov ed screw and po wer supply in an antistatic bag. Installing A C and DC P ower Supplies This section describes how to install A C and DC po wer supplies.
6 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Replacing the Cover Figure 6 Installing the Screw Step 3 Connect the po wer connector from the system board. Grasp the sides of the power connector and gently push downw ard while rocking the connector side to side.
Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 7 Replacing the Cover Caution T o fit the two sections together , it may be necessary to work them together at one end and then the other , w orking back and forth; ho wever , use care to pre v ent bending the chassis edges.
8 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Connecting the DC P ower Supply Connecting the DC P o wer Supply This section describes the DC power supply specifications and wiring. W arning This unit is intended for installation in restricted access areas.
Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 9 Connecting the DC Power Supply Figure 9 DC P ower Supply Connections W arning When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with upturned lugs.
10 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Connecting the DC P ower Supply W arning This product relies on the building’ s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 V A C, 15A U.
Installing Cisco AC and DC Power Supplies in Cisco 2500 Series Routers 11 Obtaining Service and Support Figure 11 Rear Panel Label Locations Note The System Identifier label shown in Figure 11 shows the Cisco 2520 DC system label for demonstration purposes.
12 Installing Cisco A C and DC P ower Supplies in Cisco 2500 Ser ies Routers Cisco Connection Online A v ailable 24 hours a day , 7 days a week, CCO provides a wealth of standard and value-added services to Cisco’ s customers and business partners.
An important point after buying a device Cisco 2500 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco 2500 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco 2500 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco 2500 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco 2500 Series will certainly help you make a decision on the purchase.
If you already are a holder of Cisco 2500 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco 2500 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco 2500 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco 2500 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
