Instruction/ maintenance manual of the product DS-50600 Chromalox
Go to page of 8
(Supersedes PG436-1) PG436-2 VTS 161-304901-004 JUNE, 2010 4 DATE SALES REFERENCE DIVISION SECTION Chromalox ® DS-50600, ST AR-GF , ST AR-TIP and ST AR-TG Kits For Adding Optional Kits to ST AR Radiant Heaters © 2008 Chromalox, Inc.
2 Cover (Step 4) 3 Pole Terminal Block w/Ground (Step 8) Opening for 1" Conduit Fitting (Step 8) 3 Pole Disconnect Switch On-Off Handle Chase Nipple and Gasket (Step 5) Cover (Step 3) INST ALLA TION INSTRUCTIONS INSTRUCTIONS FOR INST ALLING DISCONNECT SWITCH ON 6 AND 13.
3 Self Tapping Screw (Step 8) On-Off Handle Cover (Step 5) 3 Pole Disconnect Switch 3 Pole Terminal Block w/Ground (Step 11) Chase Nipple and Gasket (Step 6) Cover (Step 3) Mounting Bracket (Step 4) 3.
4 INSTRUCTIONS FOR INST ALLING W ALL MOUNTED ST AR-GF 1. Check voltage on heater nameplate and ST AR-GF to make cer- tain voltages are the same. If voltages do not match, consult factory . 2. The ST AR-GF will provide ground fault protection for ST AR Radiant heaters.
5 VIEW SHOWN WITH TIP OVER SWITCH ASSY COVER REMOVED MOUNTING BRACKET (STEP 4) 3/8" LOCKWASHER AND NUT (STEP 4) SELF TAPPING SCREW (STEP 8) HEAT/NO HEAT 3 POLE CONTACTOR OPENING FOR 1" CORD .
6 MAINTENANCE The Chromalox ST AR-TG tip over cutout with ground fault sensor provides a reliable and cost effective method for sensing ground faults and to shut off the heater in case of tip-over . The pur- pose of the ground fault control is to monitor for ground faults, sense potential heater failure symptoms and to protect equipment.
7 WIRING For applicable wiring diagram see T able 1 GROUND FAULT MONITOR TOGGLE SWITCH SEE NOTES ATTACHED TO AUXILLARY TERMINALS NOTES: 1. USE 90 DEG. C. MIN. WIRING. 2. USE COPPER CONDUCTORS ONLY. 3. VERIFY THAT VOLTAGE OF "STAR-TG" MATCHES VOLTAGE OF HEATER.
T A - T0 - EF Litho in U.S.A. 2150 N. RULON WHITE BLVD., OGDEN, UT 84404 Phone: 1-800-368-2493 www.chromalox.com RENEW AL P AR TS IDENTIFICA TION Kit Disconnect DS Shaft Cover “U” Shaped T erm. Block T erm. Block T oggle T oggle Switch Ground Fault Tip Over Model Switch Gasket Gasket Clamp Cont.
An important point after buying a device Chromalox DS-50600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chromalox DS-50600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chromalox DS-50600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chromalox DS-50600 you will learn all the available features of the product, as well as information on its operation. The information that you get Chromalox DS-50600 will certainly help you make a decision on the purchase.
If you already are a holder of Chromalox DS-50600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chromalox DS-50600.
However, one of the most important roles played by the user manual is to help in solving problems with Chromalox DS-50600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chromalox DS-50600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
