Instruction/ maintenance manual of the product KSA-1020 CHIEF
Go to page of 12
INSTALLATION INSTRUCTIONS Instrucciones de inst alación Installationsanleitung Instruções de Inst alação Istruzioni di inst allazione Installatie-instructies Instructions d´installation W all an.
KSA-1020 Installation Instructions 2 DISCLAIMER Milestone A V T echnologies, and its affiliated corporations and subsidiaries, (collectively , Mileston e) intend to make this manual accurate and complete.
Installation Instructions KSA-1020 3 LEGEND T ighten Fastener Apretar elemento de fijación Befestigungsteil festzie hen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixatio.
Installation Instructions KSA-1020 4 T OOLS REQUIRED FOR INST ALLA TION PA R T S 7/64" #2 1/2" 17/64" 1/2" F(1) A(1) B(2) C(4) D(1) E(2) G(2) 3" 3/8 X 1 1/4" #12 X 2 1/2&.
Installation Instructions KSA-1020 5 ASSEMBL Y AND INST ALLA TION Inst allation of Protective Rubber Edging 1. Place four strips of protective rubber edging (C) over the sharp edges located on the top and bottom of the mount (A). (See Figure 1) Figure 1 CPU Inst allation 1.
KSA-1020 Installation Instructions 6 CPU’s to be installe d. (See Figure 5) NOTE: Flanges may be reversed in order to allow for narrow CPU’s to be installed in a secure manner. If this is done, be sure to al so to remove and reinstall strap so that the buckle is facing out for easy adjustment.
Installation Instructions KSA-1020 7 Site Requirement s for Using Steel S tuds W ARNING: IMPROPER INST ALLA TION CAN LEAD TO EQUIPM ENT F ALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure.
KSA-1020 Installation Instructions 8 W a ll Mounting Using Steel S tuds or Drywall After determining the site meet s the installation requirements: 1. Identify desired mounting locati on on wall. 2. Using a stud fin d er or similar method loca te stud.
Installation Instructions KSA-1020 9 Figure 13 Mounting CPU to W all CAUTION: Overtightening screws may cause wall bracket to compress into soft wall surface resulting in difficult mount installation. 1. Ensure bracket flag is in the open position. (See Figure 2) 2.
KSA-1020 Installation Instructions 10 Figure 16 3. Install 3/8 x 1 1/4" hex head lag screw (F) through bearing (D) and bracket into hole drilled in S tep 2. (See Figure 16) 4. Ensure bracket flag is in the open position. 5. Insert four mountin g buttons into four mo unting holes on the bracket.
Installation Instructions KSA-1020 11.
KSA-1020 Installation Instructions USA/International A 8401 Eagle Creek Parkway , Savage, MN 55378 P 800.582.6480 / 952 .894.6280 F 877.894.6918 / 952 .
An important point after buying a device CHIEF KSA-1020 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CHIEF KSA-1020 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CHIEF KSA-1020 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CHIEF KSA-1020 you will learn all the available features of the product, as well as information on its operation. The information that you get CHIEF KSA-1020 will certainly help you make a decision on the purchase.
If you already are a holder of CHIEF KSA-1020, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CHIEF KSA-1020.
However, one of the most important roles played by the user manual is to help in solving problems with CHIEF KSA-1020. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CHIEF KSA-1020 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
