Instruction/ maintenance manual of the product Camaro Chevrolet
Go to page of 22
A /C -H EA T ER S Y ST EM - M A N U A L 2001 C he v r o l e t C a m a r o 2000-01 MANUAL A/C-HEATER SYSTEMS General Motors Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * WARNIN.
some of the air is recirculated through the A/C system. A/C Conditioned air is directed through dash registers. Bi-Level Conditioned air is directed through dash registers and floor outlets. A small amount of air is directed to defrost outlets. Vent Compressor does not operate in this setting.
1) Remove right instrument panel sound insulator. Remove temperature control cable from heater housing. Move temperature control knob from full cold to full hot setting. If cable binds or pulley does not rotate freely, replace cable. Set temperature control knob to detent position halfway between full cold and full hot setting.
NOTE: For additional trouble shooting information, see MANUAL A/C-HEATER SYSTEMS - TROUBLE SHOOTING article. BLOWER MOTOR 1) If blower does not operate, check HVAC fuse (20-amp) in instrument panel fuse block.
Ambient Temp. High Pressure Low Pressure F ( C) psi (kg/cm ) psi (kg/cm ) 70-80 (21-29) ( 1) ...... 115-190 (8.1-13.4) ........ 24-34 (1.7-2.4) 70-80 (21-29) ( 2) ...... 115-200 (8.1-14.1) ........ 25-37 (1.8-2.6) 80-90 (27-33) ( 1) ...... 140-215 (9.
A/C SYSTEM PERFORMANCE TEMPERATURE SPECIFICATIONS (2001 MODELS) Ambient Temp. F ( C) Center Vent Temp. F ( C) 70-80 (21-27) ( 1) ...................................... 38-48 (3-9) 70-80 (21-27) ( 2) ..................................... 40-55 (4-13) 80-90 (27-33) ( 1) .
relay harness connector terminal B2 (Dark Blue wire). If test light illuminates, go to next step. If test light does not illuminate, go to step 6). 5) Repair short to battery voltage in Dark Blue wire between blower motor relay harness connector terminal B2 and blower motor resistor harness connector terminal "C".
14) Operate blower system to verify repair. If blower motor operates normally, repair is complete. If blower motor is still inoperative, return to step 2). BLOWER MOTOR INOPERATIVE IN HIGH SPEED 2000 Models 1) Perform DIAGNOSTIC SYSTEM TEST . Go to next step.
harness connector terminal B2 (Dark Blue wire) and C1 (Purple wire). Turn ignition switch to ON position. Set mode selector switch to VENT position. Place blower motor switch in low speed position. If blower motor operates, go to step 8). If blower motor does not operate, go to step 7).
position. If blower operates in any position, problem is intermittent. Check for poor connections. loose components or damaged wiring. Repair or replace as necessary. After repair, go to step 16). If blower motor does not operate in any speed position, go to next step.
switch in VENT position. Set blower motor switch in lowest speed position. Using test light connected to ground, probe blower motor resistor harness connector terminal "C" (Dark Blue wire). If test light illuminates, go to next step. If test light does not illuminate, go to step 4).
1) Perform DIAGNOSTIC SYSTEM TEST . Go to next step. 2) Turn ignition switch to ON position. Set mode switch to VENT position. Turn blower switch to each speed position. If blower motor operates normally, go to next step. If blower motor malfunctions, go to step 4).
14) Check Light Green wire between A/C-heater control panel harness connector C2 terminal "B" and blower motor switch harness connector C1 terminal "E" located at A/C-heater control panel for open or high resistance. Repair Light Green wire as necessary.
Removal (5.7L Engine) Disconnect negative battery cable. Discharge A/C system, using approved refrigerant recovery/recycling equipment. Raise and support vehicle. Remove serpentine drive belt and tensioner. Remove compressor and condenser hose bolt. Disconnect compressor and condenser hose assembly.
2) Raise and support vehicle. Remove compressor and condenser hose assembly fitting at condenser. Discard "O" ring. Lower vehicle. Remove accumulator tube. Remove radiator air upper baffle from condenser. Remove condenser. 3) To install, reverse removal procedure.
Fig. 3: Exploded View Of A/C-Heater Assembly Courtesy of General Motors Corp. Installation 1) To install, reverse removal procedure. Transfer condensate.
screen to new evaporator. Using appropriate adhesive, install NEW evaporator core gasket in same position as original. Slide new evaporator to right until full seated in A/C-heater case. 2) Apply sealer (not epoxy) between evaporator and evaporator upper and lower case.
ring, as this will cause it to expand. Insert short screen end of orifice tube first. Evacuate, charge, and leak test A/C system. TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) Accumulator Hose Fitting At Evaporator ...........
Fig. 4: Manual A/C-Heater System Wiring Diagram (2000 Camaro & Firebird With 3.8L Engine).
Fig. 5: Manual A/C-Heater System Wiring Diagram (2000 Camaro & Firebird With 5.7L Engine).
Fig. 6: Manual A/C-Heater System Wiring Diagram (2001 Camaro & Firebird With 3.8L Engine).
Fig. 7: Manual A/C-Heater System Wiring Diagram (2001 Camaro & Firebird With 5.7L Engine) A00063334.
An important point after buying a device Chevrolet Chevrolet Camaro (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chevrolet Chevrolet Camaro yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chevrolet Chevrolet Camaro - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chevrolet Chevrolet Camaro you will learn all the available features of the product, as well as information on its operation. The information that you get Chevrolet Chevrolet Camaro will certainly help you make a decision on the purchase.
If you already are a holder of Chevrolet Chevrolet Camaro, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chevrolet Chevrolet Camaro.
However, one of the most important roles played by the user manual is to help in solving problems with Chevrolet Chevrolet Camaro. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chevrolet Chevrolet Camaro along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
