Instruction/ maintenance manual of the product 5101194 Char-Broil
Go to page of 20
04201101 WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
2 Installation Safety Precautions • • National Fuel Gas Code, NFPA 54 / ANSI Z223.1 NFPA/ANSI 58. National Electrical Code, ANSI / NFPA 70. Use appliance only with LP (propane) gas and the regulator/valve assembly supplied. Appliance installation must conform with local codes, or in their absence with .
3 T o insure your satisfaction and for follow-up service, register your product online at: www .g rillr e gistr a tion.com Table of Contents Use and Care .................................... 2-10 Safety Symbols ...............................2 Cylinder Cylinder Cylinder Cylinder Cylinder Installation Safety Precautions .
D ANGER • NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. • Never fill a cylinder beyond 80% full. • An over filled or improperly stored cylinder is a hazard due to possible gas release from the safety relief valve.
• A frosty regulator indicates gas overfill. Immediately close LP cylinder valve and call local LP gas dealer for assistance. • Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice. • T o remove gas from LP , contact an LP dealer or call a local fire department for assistance.
Hold coupling nut and regulator as shown for proper connection to LP cylinder valve. C Straight 6. An additional one-half to three quarters turn is required to complete connection. Tighten by hand only - do not use tools. NOTE: do not use this Regulator! T urn the coupling nut clockwise to tighten to a full solid stop.
WARNING Ignitor Lighting 1. Open lid during lighting. 2. Press and turn the control knob to the position. 3. T urn knob rapidly . 4. If ignition does not occur in 5 seconds, turn the burner control knob , wait 5 minutes, and repeat lighting procedure.
SOLUTION: Wait for appliance to cool. Clean burner often. Spiders and insects don’t care if your appliance is brand new or you just cleaned it. Use a hose with a nozzle attached. Forced water will wash out the web. Natural Hazard • Spiders CA UTION FACT: Sometimes spiders and other small insects climb into the burner tube.
Job Routine Cleaning Fingerprints and Smears Stubborn Stains and Discoloration Grease and Blood Burnt-on or Baked-on Foods Grease and Oil Cleaning Agents* W arm W ater , Soap, Ammonia, Detergent 3M St.
Problem Burner will not light using ignitor . Burner will not match- light. Sudden drop in gas flow or low flame. Flames blow out. Flashback... (fire in burner tube). Unable to fill LP cylinder Possible Cause — Electrode and burner are wet. — Electrode is cracked or broken, “sparks at crack”.
ST OP! Missing a part? No need to go back to the store! The store where you made your purchase does not stock parts for this item. If you need parts, whether they are missing or damaged, call the Customer Service toll free Help Line. Call us and we will gladly ship the part you need FREE OF CHAR GE.
Parts Diagram A B C C D E F F G H I J K L L M M F N O 12.
Assembly Step 1 Slide tool hooks onto one of the towel bars prior to assembly . Attach each towel bar using two . 1/4-20x3/4” machine screws DO NOT LIFT UNIT USING TOWEL BARS. 1/4-20x3/4” Machine Screw Qty: 4 Wrap/Body 55700670 Towel bar 55700667 Tool hook 1/4-20x3/4” Machine Screw Step 2 Feed burner tube through center hole of heat shield.
Step 3 Position rotary ignitor as shown below . Attach ignitor behind control panel using two . #8x1/2” self-tap screws #8x1/2” Self-Tap Screw Qty: 2 Rotary ignitor 55700666 #8x1/2” Self-Tap Scr.
Step 5 Align valve with burner tube. Figure A #10- 24x3/8” machine screws #10-24 hex/keps nuts #10x1/2” self-tap screw See for proper valve-to-burner engagement. Secure control panel to body at each end using two and two . Inside body , insert one through body into panel.
Step 8 Step 7 Lift body assembly and place onto base. Back/open-end of body assembly should face back of base. Back of base has locking casters, front has non-locking casters.
Cylinder valve must face to rear of cart once cylinder is attached. Failure to install cylinder correctly may allow gas hose to be damaged in operation, resulting in the risk of fire. CA UTION Step 9 Place cover assembly onto top. Align lower hinge holes with holes on back side of top.
18.
Please register your product online at: (If you register online, you do not need to send in this registration card.) WWW .GRILLREGISTRA TION.COM 19.
Char-Broil, LLC • Columbus, GA 31902 • Assembly Instructions © 2005.
An important point after buying a device Char-Broil 5101194 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Char-Broil 5101194 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Char-Broil 5101194 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Char-Broil 5101194 you will learn all the available features of the product, as well as information on its operation. The information that you get Char-Broil 5101194 will certainly help you make a decision on the purchase.
If you already are a holder of Char-Broil 5101194, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Char-Broil 5101194.
However, one of the most important roles played by the user manual is to help in solving problems with Char-Broil 5101194. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Char-Broil 5101194 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
