Instruction/ maintenance manual of the product LIFTMASTER MUGAPLM Chamberlain
Go to page of 16
Carton Inventory Overview The Multi-Unit Gate Access Panel (MUGAPLM) uses a digitally secure intercom link that allows it to control up to four gate operators and other accessories. It can be used with up to 63 homes and program up to 120 remote control transmitters.
2 Gate Control Unit (GCU) (not provided) Assemble Step 1: Remove GCU cover. Step 2: Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) NOTE: This step applies only if more than one GCU is being used.
3 Step 1: Press and release the Learn button on the intercom. Step 2: Within 20 seconds enter Master PIN Number on MUGAPLM. Step 3: Press “05”. Step 4: Followed by (00-63) Step 5: Then press the Call Button. Intercom will beep indicating programming is successful.
4 Step 1: On ONE repeater, set Dipswitch #1 to ON. All other Dipswitches should remain OFF. Step 2: Press Learn button on both Repeaters (within 5 seconds of each other). LED will light. Step 3: Within 20 seconds, enter Master PIN Number on MUGAPLM. Step 4: Press “05”.
Enter Master PIN Number on MUGAPLM: ? ? ? ? 0 6 Enter one of the following volume levels: 1 2 3 Enter Master PIN Number on MUGAPLM: ? ? ? ? 0 7 OR OR 1 2 3 OR OR Enter one of the following sensitivity.
6 The MUGAPLM can be set to Passive Mode to work with multiple MUGAPLM’s. The Passive MUGAPLM will become an accessory to the Active MUGAPLM. Any accessories that have been taught to the Passive MUGAPLM will have to have memories cleared and be reprogrammed to the Active MUGAPLM.
7 PIN Number Functions PIN number Function 01 Self Test Mode 03 Power-save Mode 04 Exit Power-save Mode 05 01 Call Enable MUGAPLM Learn Mode 06 (1-3) MUGAPLM Volume Control 07 (1-3) MUGAPLM Microphone.
© 2009, The Chamberlain Group Inc. 114A3890 All Rights Reserved NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
1 # # # ? ? ? ? ® Inventario de las cajas Descripción general El Panel de acceso a la puerta de unidades múltiples (MUGAPLM) usa un enlace de intercomunicador que permite controlar hasta cuatro operadores de puerta y otros accesorios. Se puede usar con hasta 63 casas y programarse con hasta 120 transmisores de control remoto.
2 Identificación Interruptor Interruptor de la GCU N.º 1 N.º 2 1 APAGADO APAGADO 2 ENCENDIDO APAGADO 3 APAGADO ENCENDIDO 4 ENCENDIDO ENCENDIDO ? ? ? ? 1 2 3 4 13 2 456789 1 0 1 1 DC AC + - COM N/C EXIT SAFETY EDGE COMMON OPEN N/O Unidad de control de puerta (GCU) (no incluidas).
3 Paso 1: Presione y suelte el botón Aprendizaje del receptor. Paso 2: En menos de 20 segundos, ingrese el número de PIN principal en el MUGAPLM. Paso 3: Presione “05”. Paso 4: Seguido por (00-63) Paso 5: Luego presione el botón Llamada. El intercomunicador emitirá una señal sonora para indicar que la programación ha sido exitosa.
4 Paso 1: En UN repetidor, configure el conmutador DIP N.º 1 en ENCENDIDO. Todos los demás interruptores DIP deben permanecer APAGADOS. Paso 2: Presione el botón Aprendizaje en ambos repetidores (con máximo 5 segundos de diferencia entre sí). El LED se encenderá.
? ? ? ? 0 6 1 2 3 ? ? ? ? 0 7 1 2 3 5 ? ? ? ? 0 8 1 2 3 ? ? ? ? 0 9 # # # ? ? ? ? 7 # # # ? ? ? ? 5 1 ? ? ? ? 9 Ingrese el número de PIN principal en el MUGAPLM: Ingrese uno de los siguientes niveles.
6 ? ? ? ? 0 5 ? ? ? 5 6 ? 0 1 ? ? ? ? 5 5 1 2 3 ? ? ? ? 5 2 ? ? ? ? 5 3 ? ? ? ? 5 4 El MUGAPLM se puede configurar en el modo Pasivo para trabajar con múltiples MUGAPLM.
7 Número de PIN Función 01 Modo de prueba automática 03 Modo de ahorro de energía 04 Salir del modo Ahorro de energía 05 01 Llamada Habilitar el modo Aprendizaje del MUGAPLM 06 (1-3) Control de v.
© 2009, The Chamberlain Group Inc. 114A3890 Todos los derechos reservados AVISO: Para cumplir con las reglas de la FCC y/o de Canadá (IC) ajustes o modificaciones de este receptor y/o transmisor están prohibidos, excepto por el cambio de la configuración del código o el reemplazo de la batería.
An important point after buying a device Chamberlain LIFTMASTER MUGAPLM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chamberlain LIFTMASTER MUGAPLM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chamberlain LIFTMASTER MUGAPLM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chamberlain LIFTMASTER MUGAPLM you will learn all the available features of the product, as well as information on its operation. The information that you get Chamberlain LIFTMASTER MUGAPLM will certainly help you make a decision on the purchase.
If you already are a holder of Chamberlain LIFTMASTER MUGAPLM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chamberlain LIFTMASTER MUGAPLM.
However, one of the most important roles played by the user manual is to help in solving problems with Chamberlain LIFTMASTER MUGAPLM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chamberlain LIFTMASTER MUGAPLM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
