Instruction/ maintenance manual of the product HE60R Chamberlain
Go to page of 16
Installation and operating instructions for HomEntry garage door opener Model HE60R Chamberlain Australia Pty Ltd Phone toll free 1800 638 234 Fax toll free 1800 888 121 Chamberlain New Zealand Ltd Phone toll free 0800 637 546 Fax toll free: 0800 653 663 www .
.
The Protector System must be used for all installations where the closing force as measured on the bottom of the door is over 400N (40kgf). Excessive force will interfere with the proper operation of the Safety Reverse System or damage the garage door .
T ools Required 2 1. Ladder (or similar device to safely support door weight) 2. Adjustable wrench for U-bolts already installed on the door 3. 8mm socket, 10mm socket and 13mm extended socket and socket wrench 4. 30mm socket extension (for minimum sideroom installations) 5.
3 Door Requirements 3 Ensure that there is at least 45mm from the edge of the curtain to the edge of the bracket. If the roller door drums are on the edge of the curtain or are of small diameter additional clearance maybe required. If the drums are more than 60mm from the curtain edge or of small diameter extension poles maybe required.
T esting the door Disable all locks and remove any ropes connected to the garage door . Complete the following test to ensure your door is well balanced, and not sticking or binding: • Lift the door to about halfway and then release it. The door should remain suspended entirely by its spring.
5 Preparing the Opener 7 For left hand side installations the wire jumper should be removed . Place the Opener in Manual Release mode. • Pull the release cord down and across to engage the ball into the cup. The drive forks should now be able to be moved manually .
6 Installation steps 8 FOR RIGHT HAND INST ALLA TIONS (REFER SECTION 7, page 5) • Ensure that the opener position jumper (wire connector) is installed (refer Section 7, page 5). • Place the opener in manual release mode (refer Section 7, page 5). • Open the roller door fully .
Pinning the Door 11 Use two metal self tapping metal screws provided to hold the curtain to the door drum. Note: A ballooning may delay the safety response and can compromise your garage door security . • Pull the release cord down Firmly to disengage the motor .
Setting the Limits The T ravel Limits regulate the points at which the door will stop when moving UP or DOWN. During the SetUp procedure, the motor will run and operate the door . The Opener must be fully installed on the door and all installation steps completed before proceeding.
Setting the Force The force, as measured on the closing edge of the door , should not exceed 400N (40kg). If the closing force is measured to more than 400N, the Protector System must be installed. See Section 16. The force setting regulates the amount of power required to open and close the door .
10 Install the Protector System™ (Safety Beams) Install this accessory for all installations where the closing force as measured on the bottom of the door is over 400N (40kgf). After opener has been installed and adjusted, The Protector System™ accessory can be installed.
CARE OF YOUR OPENER When properly installed, your opener will provide high performance with minimal maintenance. The opener does not require additional lubrication. Limit and Force Settings: These settings must be checked and properly set when the opener is installed.
12 Troubleshooting 1. The opener doesn't operate from either the GREEN start button or the remote controls: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box. • Have you disabled all door locks? Review installation instruction warnings on page 1.
13 OPERA TION OF YOUR OPENER Y our opener can be activated by any of the following devices: • The green start button Hold the button down until door starts to move. • The W all Control, Outside Keylock or Keyless Entry System (if you have installed any of these accessories).
Liability – Australia only Under no circumstances shall the Seller be liable for consequential, incidental or special damages arising in connection with the use, or inability to use, the Unit.
An important point after buying a device Chamberlain HE60R (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chamberlain HE60R yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chamberlain HE60R - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chamberlain HE60R you will learn all the available features of the product, as well as information on its operation. The information that you get Chamberlain HE60R will certainly help you make a decision on the purchase.
If you already are a holder of Chamberlain HE60R, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chamberlain HE60R.
However, one of the most important roles played by the user manual is to help in solving problems with Chamberlain HE60R. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chamberlain HE60R along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
