Instruction/ maintenance manual of the product CR550 Chamberlain
Go to page of 16
CR550 Rolling Garage Door Opener Installation and Operating Instructions www .chamberlainanz.com Owners Copy: Please keep these instructions for future reference This manual contains IMPORT ANT SAFETY.
1 CONTENTS P AGE SAFETY INSTRUCTIONS . . . . . . . .1 CART ON INVENT ORY . . . . . . . . . .2 TOOLS REQUIRED . . . . . . . . . . . .2 DOOR REQUIREMENTS . . . . . . . .2 PREP ARE & TEST THE DOOR . .3-4 INST ALLA TION . . . . . . . . . . . . . .5-6 CONNECT ELECTRIC POWER .
2 1. Instruction manual (this document) 2. W arning and risk of entrapment labels 3. Hardware bag 4. Release handle, cord and risk of entrapment card 5. 3 Channel mini transmitter (2) 6. W all or visor mounted transmitter 7. Stop collar 8 . Clamp bracket and plate 9.
TESTING THE DOOR Complete the following test to ensure your door is well balanced, and not sticking or binding: • Disable all locks and remove any ropes connected to the garage door . • Lift the door to about halfway and then release it. The door should remain suspended entirely by its spring.
4 PREP ARING THE OPENER 7 For left hand side installations the wire jumper should be removed . For right hand side installations the wire jumper should be in place (factory installed).
5 INST ALLA TION STEPS 9 FOR RIGHT HAND INST ALLA TIONS • Ensure that the opener position jumper (wire connector) is installed (refer Section 7). • Place the opener in manual release mode (refer Section 1 1). • Open the roller door fully . For safety , tie a rope around the door (as shown).
1 0 • Thread one end of the rope through the hole in the top of the red handle so “NOTICE” reads right side up as shown. • Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping. • Thread the other end of the rope through the loop of the manual release cable.
T ravel limits regulate the points at which the door will stop when moving UP or DOWN. During the set up procedure, the motor will run and operate the door . T he opener must be fully installed on the door and all installation steps completed before proceeding.
T he force, as measured on the closing edge of the door , should not exceed 400 N (40 kg). If the closing force is measured to more than 400 N, The Protector System TM (IR Beams) must be installed (refer section 16). The force setting regulates the amount of power required to open and close the door .
NOTE: This accessory must be used for all installations where the closing force as measured on the bottom of the door is over 400 N (40 kgf). After the opener has been installed and adjusted, the Protector System™ (IR Beams) accessory can be installed.
10 ADDING transmitters using the learn button • Press and hold down the transmitter button you wish to program to the opener . • The orange LED will flash continuously to indicate it is receiving signal from the transmitter . • Press and release the learn button on the opener .
Wireless Keypad 8747AML Using the (purple) learn button: 1. Press and release the (purple) learn button (1) on the opener (the orange LED will light). 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad (2), then press and hold the ENTER button.
12 1 2 L O C K L I G H T 1.Multifunction control panel Connect white/red wire to the red “wired wall control” quick connect terminal and the white wire to the white “wired wall control” quick connect terminal.
TROUBLESHOOTING 1.The opener doesn't operate from either the GREEN start button or the transmitters: • Does the opener have electric power? Plug a lamp into t he outlet. If it doesn't light, check the fuse box. • Have you disabled all door locks? Review installation instruction warnings on page 1.
14 O PERA TION OF YOUR OPENER Y our opener can be activated by any of the following devices: • The GREEN start button Hold the button down until door starts to move. • The wall control, outside keyswitch or keyless e ntry system (if you have installed any of these accessories).
15 © 2012 The Chamberlain Group, Inc 1 14B4542B TM T rademark of The Chamberlain Group, Inc. ® Registered Trademark of The Chamberlain Group, Inc. Chamberlain Limited W arranty , we may , subject to your other rights and remedies as a consumer , charge you a fee to repair , replace and/or return the Unit to you.
An important point after buying a device Chamberlain CR550 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chamberlain CR550 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chamberlain CR550 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chamberlain CR550 you will learn all the available features of the product, as well as information on its operation. The information that you get Chamberlain CR550 will certainly help you make a decision on the purchase.
If you already are a holder of Chamberlain CR550, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chamberlain CR550.
However, one of the most important roles played by the user manual is to help in solving problems with Chamberlain CR550. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chamberlain CR550 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
