Instruction/ maintenance manual of the product ATS 2113X Chamberlain
Go to page of 32
Owner’s Manual Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System ■ ® is connected and properly aligned. Periodic checks of the opener are required to ensure safe operation.
2 Introduction 2-5 Safety symbol and signal word review . . . . . . . . . . . . . . . . . . . . .2 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Preparing your garage door Before you begin: Disable locks. • Remove any ropes connected to garage door. • Complete the following test to make sure your garage door is • balanced and is not sticking or binding: Lift the door about halfway as shown.
4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 18 for details. Support bracket & fastening hardware is required. See page 11.
5 Straight Door Arm Door Bracket Plate Door Bracket Safety Labels and Literature "C" Wrap (2) 2 -Conductor Bell Wire White & White/Red Curved Door Arm Rail Styrofoam Chain Pulley Bracket.
6 ASSEMBLY STEP 1 Attach the Rail to the Motor Unit To avoid installation difficulties, do not run the garage door opener until instructed to do so. Place the opener on packing material to protect the cover. • Remove the (2) 5/16"-18x1/2" washered bolts mounted in the • top of the motor unit.
7 ASSEMBLY STEP 3 Tighten the Chain Spin the inner nut and lock washer down the threaded shaft, • away from the trolley. To tighten the chain, turn outer nut in the direction shown. • As you turn the nut, keep the chain from twisting. When the chain is approximately 1/2" (1.
8 INSTALLATION STEP 1 Determine the Header Bracket Location Close the door and mark the inside vertical centerline of the 1. garage door. Extend the line onto the header wall above the door.
9 INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. DO NOT install the header bracket over drywall.
10 Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Chain Pulley Bracket Temporary Support Header Wall Garage Door Rail Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Cha.
11 INSTALLATION STEP 4 Position the Opener SECTIONAL DOOR ONLY A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. Raise the opener onto a stepladder. You will need help at this • point if the ladder is not tall enough. Open the door all the way and place a 2x4 laid flat on the top • section beneath the rail.
12 Drywall Anchors Insulated Staples Screw 6ABx1-1/2" Lighted Door Control Button HARDWARE SHOWN ACTUAL SIZE To prevent possible SERIOUS INJURY or DEATH from electrocution: Be sure power is not connected BEFORE installing door • control. Connect ONLY to 24 VOLT low voltage wires.
13 INSTALLATION STEP 7 Install the Light Install a 75 watt maximum light bulb in the socket. The light • will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the light will turn OFF. If the bulb burns out prematurely due to vibration, replace with • a “Garage Door Opener” bulb.
14 INSTALLATION STEP 9 Electrical Requirements To avoid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
15 Invisible Light Beam Protection Area Safety Reversing Sensor 6" (15 cm) max. above floor Safety Reversing Sensor 6" (15 cm) max. above floor Facing the door from inside the garage INSTALL.
16 Inside Garage Wall “C” Shaped Wrap Mounting Bracket with Square Holes 1/4-20x1/2" Carriage Bolts 1/4"-20 Lock Nuts Drill 3/8" Holes Garage Door Track Figure 3 Garage DOOR Track I.
17 Hex Bolt 1/4-20 x 1-1/2" "C" Wrap Sensor with Wire Wing Nut Indicator Light Figure 6 Invisible Light Beam Protection Area Safety Reversing Sensor Safety Reversing Sensor Connect Wire.
18 HARDWARE SHOWN ACTUAL SIZE Figure 2 Figure 1 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. INSTALLATION STEP 11 Fasten the Door Bracket A horizontal brace should be long enough to be secured to 2 vertical supports.
19 INSTALLATION STEP 12 Connect Door Arm to Trolley SECTIONAL DOORS ONLY Make sure garage door is fully closed. Pull the emergency • release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2" (5 cm) as shown in Figures 1, 2 and 3.
20 ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener, press the Door Control push bar. Run the opener through a complete travel cycle.
21 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door. If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction.
22 ADJUSTMENT STEP 3 Test the Safety Reversal System TEST With the door fully open, place a 1-1/2" (3.8 cm) board (or a • 2x4 laid flat) on the floor, centered under the garage door. Operate the door in the down direction. The door must reverse • on striking the obstruction.
23 OPERATION Using Your Garage Door Opener Your opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. Activate your opener with any of the following: The hand-held Remote Control: • Hold the large push button down until the door starts to move.
24 To Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually. To reconnect the door to the opener, press the door control push bar. The lockout feature prevents the trolley from reconnecting automatically.
25 Having a Problem? The opener doesn’t operate from either the Door Control or 1. the remote control: Does the opener have electric power? Plug a lamp into the • outlet. If it doesn’t light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.
26 The 300 Series remote control works only with door openers and light controls having a purple “Learn” button. Programming instructions are described and illustrated below. The additional push buttons can also activate other garage door openers and/or light controls.
27 Press and release the “learn” button on 1. motor unit. The learn indicator light will glow steadily for 30 seconds. Within 30 seconds, enter a four digit 2. personal identification number (PIN) of your choice on the keypad. Then press and hold the enter button.
28 Multi-Function Door Control (Optional) OPERATION OF THE MULTI-FUNCTION DOOR CONTROL Press the push button to open or close the door. Press again to reverse the door during the closing cycle or to stop the door while it’s opening. Light feature Press the Light button to turn the opener light on or off.
29 6 UP CEILING MOUNT ONLY 10 1 NOTICE 3 5 4 9 8 11 12 2 7 2 1 3 4 5 Installation Parts REPAIR PARTS Rail Assembly Parts KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A2780 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 CD1008 8 Foot (2.
30 Motor Unit Assembly Parts 9 7 12 13 14 15 18 4 8 11 17 10 16 3 5 6 18 15 Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 1 2 KEY PART NO. NO. DESCRIPTION 41C5069 Rail support bracket assembly kit 1.
31 LOCK LI GH T ACCESSORIES 370LM CD1008 1702LM Outside Quick Release: Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley. 8 Foot (2.44 m) Complete Rail: To allow an 8 foot (2.
© 2010, The Chamberlain Group, Inc. 114A3155E All Rights Reserved LIFTMASTER ® SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Std.
An important point after buying a device Chamberlain ATS 2113X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chamberlain ATS 2113X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chamberlain ATS 2113X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chamberlain ATS 2113X you will learn all the available features of the product, as well as information on its operation. The information that you get Chamberlain ATS 2113X will certainly help you make a decision on the purchase.
If you already are a holder of Chamberlain ATS 2113X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chamberlain ATS 2113X.
However, one of the most important roles played by the user manual is to help in solving problems with Chamberlain ATS 2113X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chamberlain ATS 2113X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
