Instruction/ maintenance manual of the product 1000SD Chamberlain
Go to page of 36
TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3.
Start by re viewing these important safety alert symbols: 2 Safety alert symbol re view ............................................2 Safety information and precautions ..............................3 T esting your garage door for binding & balance .
3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice.
4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2).
Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.
ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex.
ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door .
• Open your door to the highest point of trav el as shown. Dra w an inter- secting horizontal line on the header wall 3" abo ve the high point. This height will provide tra vel clearance for the top edge of the door .
Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door .
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket.
Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door .
The safety re versing sensor must be connected and aligned correctly bef ore the garage door opener will move in the do wn direction. This is a requir ed safety device and cannot be disabled. Installation pr ocedur es ar e the same for sectional and one-piece doors.
Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el.
Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring.
Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley .
Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener .
In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on.
T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet.
T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet.
In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on.
Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener .
Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley .
Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring.
Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el.
Adjustment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door.
Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door .
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket.
Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door .
Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control(s) or remote control transmitter(s). A moving garage door could injure or kill someone under it.
ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door .
ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex.
Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.
4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2).
3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice.
Index Access Door/Outside Quick Release Accessory .........................................................................................................31, 34 Electrical Safety W arnings .............................................................
TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3.
An important point after buying a device Chamberlain 1000SD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chamberlain 1000SD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chamberlain 1000SD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chamberlain 1000SD you will learn all the available features of the product, as well as information on its operation. The information that you get Chamberlain 1000SD will certainly help you make a decision on the purchase.
If you already are a holder of Chamberlain 1000SD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chamberlain 1000SD.
However, one of the most important roles played by the user manual is to help in solving problems with Chamberlain 1000SD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chamberlain 1000SD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
