Instruction/ maintenance manual of the product BC2-IT Cecilware
Go to page of 21
BREW CENTER-IT, COFFEE BREWING EQUIPMENT Cecilware sells value... Worldwide 43 -05 20th Avenue, Long Island City, NY 11105 TEL: 718-932-1414 FAX: 718-932-7860 MODELS Single BC301-IT Twin BC2-IT BC302-.
2 SPECIFICATIONS ELECTRICAL SPECIFICATIONS MODEL NO. BC301-IT BC2-IT BC302-IT Volts 120/240 120/240 120/240 Watts 4100 6200 6200 Amps 18 27 27 Wall Outlet (Receptacle) Power Cord CE202 – 30A optional 6-20R 6-30R 6-30R All Brew Centers are single phase with 3 wires plus a ground with cord and plug, except Eport 220V, 1 PH, (UROPEAN).
3 FEATURES AND BENEFITS OF THE DIGITAL, MEMBRANE CONTROL TOUCH PAD BREWER 1. 100% Solid State Control for improved reliability. 2. Modular design and reduced component count for ease of service. 3. Optional Low Water Temperature Lockout to prevent dispen sing at water temperatures below an adjustable threshold.
4 INSTALLATION AND OPERATING INSTRUCTIONS Warranty is void if the Brewer is connected to any Voltage other than the Voltage specified on the data label of the Brewer. UNPACKING AND INSPECTION Carefully unpack the Brewer by cutting the straps and lifting the carton off the Brewer.
5 CANCEL POWER CANCEL microprocess or driven HOT WATER CAUTION PROGRAMMING INSTRUCTIONS The following is a Functional Description of the Single Station Brewer : Modes of Operation - Overview Initialization Mode – This mode is only active during the first few seconds after a “power-on” or system reset.
6 MODES OF OPERATION – DESCRIPTIONS Initialization Mode: The following screen signifies the presence of this mode: CECILWARE &&&&& REV #.# Description – This mode is active only during the first few seconds after “power-on”.
7 Brewing State BREWING DDD K MM:SS HH:MMP Description – This screen is displayed when a Brew Cycl e is in progress. The time remaining in the Brew Cycle is displayed in the lower left-hand corner of the screen (depicted as “MM:SS”). The Brew Key LED will blink in this state.
8 SERVICE MODE Description – The main function of Service Mode is to gi ve qualified personnel the ability to configure the system to meet the requirements of each installation.
9 INFUSION TIME INFUSION TIME ## SECONDS Description – The Infusion Time is the amount of time that the system will dispense (infuse) hot water into the grinds during the Pre-Infusion process.
10 TEMPERATURE SENSOR CALIBRATION TEMP SENSOR CAL ARE YOU SURE ? Description – The Temperature Sensor Calibration allows the user to offset (calibrate) the displayed water temperature to a reference thermometer. Instructions – Use the [Arrow] Keys to adjust (calibrate) the displayed temperature to match the reference thermometer.
11 WEEKDAY TIME OFF WEEKDAY TIME OFF ##:## #M Description – The Weekday Time OFF function allows the user to set the required weekday turn OFF time. WEEKEND TIMER WEEKEND TIMER ON/OFF Description .
12 ERROR MODE Description – The main function of Error Mode is report any system malfunctions and to disable the unit The system must be “powered down” usi ng the Power Key located on the membra.
13 PARTS IDENTIFICATION BC301-I T BC2-IT BC302-IT I TE M P/N QT Y P/N QT Y DESCRIPTION 1 SF26A 1 SB49A 1 CABINET TOP COVER 2 ---- NG35A NG37A -- 1 1 --- NG40A NG36A NG39A -- 1 1 1 TOUCH PAD LABEL: BC1.
14 TOP CABIN - PARTS IDENTIFICATION ITEM P/N BC301-IT QTY P/N BC2-IT BC302-IT QTY DESCRIPTION 1 L656A 1 L656A 2 HI-LIMIT 2 L671A 1 L671A 1 THERMISTER PROBE 3 K355Q 1 K355Q 1 WATE R LEVEL CONTROL PROBE.
15 BOTTOM CABIN OPEN VIEW BOTTOM CABIN - PARTS IDENTIFICATION ITEM P/N BC301-IT QTY P/N BC2-IT BC302-IT QTY DESCRIPTION 1 L069A 1 L069A 1 POWER SWITCH 2 CD257 1 CD257 1 WATER INLET VALVE 3 B083A 1 B08.
16 CLEANING AND SANITIZING SANITIZING: All food dispensing units should be sanitized periodically . All parts to be sanitized must be cleaned first. To prepare a sanitizing solution: ADD 2 TSP. OF LIQUID CLOROX BLEACH (5.25% CONCENTRATION) TO 1 GALLON OF WATER AT ROOM TEMPERATURE (70°- 90°F).
17 TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit.. Before any attempt to replace a component be sure to check all electrical connections for proper contact PROBLEM PROBABLE CAUSE REMEDY 1.
18 SPECIAL COMPONENTS TEST AND ADJUSTMENTS 1) WATER INLET VALVE (SOLENOID) TEST ( Located inside bottom cabin ) Turn power off from touchpad. If the water level rises inside the tank, and shoots out of the overflow, the Water Inlet Valve is leaking. Disconnect wires from the Water Inlet Valve coil and connect a 2 wire line cord to the ter minals.
19 5) CHECK DISPENSE VALVES FOR LIME BUILD-UP ( Located inside top cabin ) Drain The Water Tank To Just Below The Level Of The Dispense Valves. Remove The Valves And Clean. You Can Take These Valves Apart By Hand As Shown. Replace The Assembly As Needed.
20 120VAC T1 CH82A 2+ 1- THERMISTOR L617A SEE DETAIL-1 275V 0.1uf C1 HEATER TANK 3KW MT1 G SP1 SWITCH S1 POWER MT2 PROBE LEVEL OVER-FLOW HOSE SAFETY RELAY L55 3A K2 4 K1 3 WARM ER 100W #4 #3 #2 DILUTI.
21 THERMISTOR #L617A OVER TEMPE RATURE SENSOR ASSEMBLY SEE DATAIL-1 #M683A TEE #10054 TRIAC L623A 40A THERMISTOR L671A J2 J6 BATTERY- PANASONIC #CR2030 OR EQUIVALENT LCD CONT ROL BOARD L669A J1 TO KEY.
An important point after buying a device Cecilware BC2-IT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cecilware BC2-IT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cecilware BC2-IT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cecilware BC2-IT you will learn all the available features of the product, as well as information on its operation. The information that you get Cecilware BC2-IT will certainly help you make a decision on the purchase.
If you already are a holder of Cecilware BC2-IT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cecilware BC2-IT.
However, one of the most important roles played by the user manual is to help in solving problems with Cecilware BC2-IT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cecilware BC2-IT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
