Instruction/ maintenance manual of the product FW821 CDA
Go to page of 16
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Important The manufacturer cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that we reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
3 This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109 .
4 Before first use Y ou must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior .
5 Use • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator . W arm food should be allowed to cool to room temperature before being put into the refrigerator .
6 W e recommend initially setting the temperature control in mid range for the first 24 hours then adjusting the temperature up or down from this point as your personal preference. Care and cleaning Always disconnect the appliance from the power before any cleaning or maintenance.
7 T roubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CD A Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance.
8 fig. 2 1770 45 57 545 540 1770- 1788 min. 30 560-570 545 min = airflow If there is water in the lower part of the refrigerator compartment • The drain hole in the channel at the back of the compartment is clear . Please note: The LED lighting cannot be replaced without a service call.
9 V entilation The main consideration when installing any refrigeration unit into a fitted kitchen is ventilation. The heat removed from the cooling compartment needs to be dissipated into the atmosphere. Incorrect ventilation can lead to premature compressor failure, ex cessive power consumption and total system failure.
10 The open channel at the rear is clearly shown. For the correct operation of the appliance it is important that the top of the housing unit is not blocked o . A channel depth of 40-50mm is normal with most units. A hole is shown in the base shelf of the unit; this allows air to be drawn over the compressor & heat ex change.
11 R eversing the door It is possible to reverse the door on this appliance, if required. T o do so, follow the steps below: 1. L oosen the top hinge fixing screws and remove the top hinge, taking care to support the weight of the door . 2. Lift the door from the bottom hinge and place on a soft surfaceto protect the door from damage.
12 Mounting the Fascia Door • Using a screwdriver , fix the mounting brackets to the appliance door , as shown in figure 5. • Position the appliance within the unit. Ensure that there is a gap of 3 to 4 mm between the non-hinged side and the cabinet wall.
13 Electrical Iinformation W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse.
14 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL O W must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W .
15.
Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
An important point after buying a device CDA FW821 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CDA FW821 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CDA FW821 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CDA FW821 you will learn all the available features of the product, as well as information on its operation. The information that you get CDA FW821 will certainly help you make a decision on the purchase.
If you already are a holder of CDA FW821, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CDA FW821.
However, one of the most important roles played by the user manual is to help in solving problems with CDA FW821. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CDA FW821 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
