Instruction/ maintenance manual of the product CI921 CDA
Go to page of 20
1 Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 User Information The room must be adequately ventilated to avoid the backflow of gases into the room from appliances burning gas or any other fuels.
3 flammable substances in the tumble dryer . • Attempt to dry dripping wet articles. • Dry unwashed items in the tumble dryer . • Dry wool or wool mixture articles unless the article is labelled as suitable.
4 Important This appliance must only be used for the purpose for which it is intended, i.e. domestic use . Any other use could be dangerous and may lead to premature failure of the appliance. The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product.
5 CE Declarations of Conformity: This appliance has been designed, constructed and marketed in compliance with safety requirements of EEC Directives 2006/95/ EEC & 2014/35/EU (L ow voltage) and requirements of EMC Directives 2004/108/EEC & 2014/30/EU .
6 Use and Controls 1. Programme selector: Choose the final dryness of the load by selecting the desired dryness setting (see the programme chart). The dryer will stop automatically when the chosen dryness is achieved. 2. Heat settings: High – For fabrics insensitive to higher temperatures, such as cotton.
7 Programme Chart Programmes 1-7 can be operated on either full heat or half heat setting and include a 12 minute cool-down period at the end of the cycle, followed by the automatic anti-crease cycle. Programme 8 operates without the heater (regardless of the heat switch setting), circulating air through the dryer at the ambient temperature.
8 T o Run a Programme • Sort out the clothes into groups of similar fabrics and colours. Check the care label inside the garment. W e suggest that a fabric conditioner be used to reduce static electricity . Delicate articles e.g. tights should be placed inside a pillowcase.
9 • The drum will begin to turn, and will stop when the clothes are dry . The drum will rotate clockwise and anticlockwise during the programme alternately to reduce creasing.
10 Use and Controls Should the clothes dry before the cycle has finished the thermostat will automatically switch o the heater to prevent over drying and save energy although the drum will still rotate. When drying large items such as sheets, we suggest you stop the dryer to redistribute the load.
11 Suppliers name or trade mark CDA Model identifier CI921 Rated capacity at full load 7kg Appliance type Air Vented Energy efficiency class C Energy consumption of the appliance* 519kWh Automatic/non-automatic Automatic EU Ecolabel N/A E dry 4.39kWh E dry½ 2.
12 Care and Maintenance Cleaning The Filter The filter is found, by opening the door (fig.2.) and must always be in position when drying items in the appliance. T o allow the dryer to operate eciently the filter should be cleaned after each drying cycle.
13 T roubleshooting If the clothes are not dry after normal drying time: - Check that the filter is clean. - Check that you used the correct heat setting. - Check that the vent hose is not blocked (sometimes a strong wind may cause a back pressure). - Check that you have not set the timer within a cool down period.
14 Installation / V enting This appliance is fully compatible with any 600mm deep kitchen units and complies with stringent EEC regulations. Y our dryer is supplied with a vent hose which will extend to appro ximately 2.4 m. W e strongly recommend that this is vented through the wall with the attachment provided.
15 PLEASE NO TE: The air vent at the front of the appliance must never be covered or blocked in any way as this will impair the functioning of the appliance and could cause it to overheat.
16 R eversing the Door The door on the dryer can be positioned either with the left or right hand hinging, as shown in fig. 6. Please note: power tools must not be used when reversing the door . How to reverse the door Open the door Undo screw A, remove switch strike B and replace screw A.
17 Electrical Information W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse.
18 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL OW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL OW .
19.
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu www .cda.eu Please contact our Customer Care Department for Service on the details below Customer Care Department The Group L td.
An important point after buying a device CDA CI921 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CDA CI921 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CDA CI921 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CDA CI921 you will learn all the available features of the product, as well as information on its operation. The information that you get CDA CI921 will certainly help you make a decision on the purchase.
If you already are a holder of CDA CI921, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CDA CI921.
However, one of the most important roles played by the user manual is to help in solving problems with CDA CI921. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CDA CI921 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
