Instruction/ maintenance manual of the product CI240WH CDA
Go to page of 24
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshir e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
Cont ents Page 1 Important information Page 2 W arnings Page 3 W ashing machine specifications Page 4 Unpacking the washing mac hine and removing the tr ansit bolts Page 5 Connecting to the mains w a.
Important This appliance must only be used for the purpose f or which it is intended, i.e. domestic use. An y other use could be dangerous and ma y lead to pr emature failur e of the appliance. The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product.
W ashing Mac hine Specifications Ac cessories 71 w a s h i n g m a c h i n e Water inlet hose specifications Drain hose Work top Power cord Control panel Detergent dispenser Stainless steel drum Filt.
Unpacking the W ashing Machine • Remove the base, c orner protect ors and top cov er (Figure 1). Remo ving the T r ansit Bolts • Remove the scr ews holding the plastic covers to the bac k of the washing machine (Figur e 2 and 3). • Loosen and r emove the 3 transit bolts (Figur e 3).
Connecting t o the Mains W ater Supply The water supply hose is located inside the drum. • Connect the bent end of the hose to the thr eaded inlet of the electrov alve located at the r ear of the washing machine. • Connect the other end of the hose to the w ater intake.
Lev elling • T o reduce the noise level fr om the washing machine and to pr event unnecessary movement during use, you should ensur e the washing machine is level using the adjustable feet. • First, fix and level the r ear feet. When they ar e properly fix ed, secure the metal locknut tightly against the underside of the w ashing machine.
Electrical information W arning! This appliance must be earthed. The mains le ad of this appli anc e has bee n fitt ed wit h a BS 1 363A 1 3 amp fused plug. T o chan ge a fuse in th is type of plug, follow the steps below: 1. Remove the fuse cover and fuse.
Befor e First Use • When your washing machine has been corr ectly installed, we rec ommend that you pre-clean the mac hine. This is to check that the inst allation, the connections and the drainage .
Pr eparing Garments for W ashing Prepar ation • Befor e placing the clothes in the drum, make sur e all the pockets ar e empty (Figure 1 0). Any small objects may bloc k the drain pump.
Deter gents and Additiv es Y our washing machine’s deter gent dispenser has three compartments. • Add the deter gent or additive to the detergent dispenser bef ore st arting the wash progr amme (Figure 1 4). The deter gent dispenser is designed to allow the use of liquid deter gents rather than adding them to the drum.
Selecting the W ash Pr ogr amme T o select a wash progr amme: • T urn the progr amme selector dial clockwise to the desir ed function. • The display on the contr ol panel will light up. • Press the S tart/P ause button to begin the pr ogramme. fig.
Selecting the W ash Pr ogr amme When you select the pr ogramme, the following inf ormation will be displayed: 1 . W ash progr amme phases: Prewash W a s h Rinse Spin-drying and draining 2. Spin speed 3. Programme number (f or a few seconds) and then pr ogramme duration.
W ashing Machine Pr ogr ammes Cotton/Linen delicate colours very light soil Cotton/Linen whites/colours very light soil Cotton/Linen delicate colours light soil Cotton/Linen fast colours light soil Co.
W ashing Machine Pr ogr ammes 0,10/59 0,25/30 0,30/59 0,60/59 1,52/59 2,20/64 1,50/64 0,10/45 0,20/45 0,40/45 1,00/45 0,05/55 0,45/55 0,05/25 0,05/0 0,00/0 50 30 52 57 80 110 100 50 50 55 70 30 40 23 .
Spin Speed Selection and Anti-Cr ease Y ou should first select the wash progr amme and then select the wash options (Changing the progr amme cancels the pr eset selected options).
Time Dela y Time dela y selection button • A delay of up to 24 hour s can be selected. The delay must be select ed after choosing the wash pr ogramme. • T o select the hours of delay , press the time delay but ton (Figure 24). Eac h time the button is pressed the dela yed start of washing is increased by one hour .
St arting Up Start/P ause button • T o start up the washing machine y ou have to pr ess the Start/Pause butt on (Figure 2 7). • The time remaining (in minut es) until the end of the progr amme will appear on the display at all times.
W ash Pr ogr amme Phases and Po wer Cuts Progr amme Phases • When the progr amme is running, the programme phase and the time r ema inin g w ill ap pear on th e di spl ay (F igur e 3 0). • The active phases will appear successiv ely at the top of the display as the programme pr ogresses (Figure 30).
fig. 32 fig. 33 18 Maintenanc e • After each w ash, leave the door open f or a while to allow the air to cir culate freely inside the machine. • From time t o time, depending on the hardness of your w ater , it is recommendable to run a full w ash cycle using a decalcifying product.
Cleaning the Filter • Clean the accessible filter if the drain pump is bloc ked by any foreign objects. • Open the kickplate c over with the aid of a coin and by gently pulling open (Figure 34). • Place a container under the drain pump filt er to collect any wat er that comes out of it (Figure 35).
Safety and T r oubleshooting • If you detect any pr oblems with your washing machine, y ou will probably be able to r ectify them yourself by consulting the following instructions. • If this is not the case, unplug the appliance and contact the tec hnical assistance number .
Pr oblems Why doesn’t the w ashing machine dr ain or spin-dry? • If this failure is detected, F02 will appear on the displa y. The reasons f or the F02 indicator may be the f ollowing: • The wa shin g m ac hin e d ra in p ump bl oc ked , b uild ing dr ainag e p ipe s bl oc ke d, o r i nco rr ect p ump el ectr ica l c onn ect ion.
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshir e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu Passionate about style T o contact our Cust omer Care Department, or f or Service, please contact us on the det ails below .
An important point after buying a device CDA CI240WH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CDA CI240WH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CDA CI240WH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CDA CI240WH you will learn all the available features of the product, as well as information on its operation. The information that you get CDA CI240WH will certainly help you make a decision on the purchase.
If you already are a holder of CDA CI240WH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CDA CI240WH.
However, one of the most important roles played by the user manual is to help in solving problems with CDA CI240WH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CDA CI240WH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
