Instruction/ maintenance manual of the product MO1305-EA Casio
Go to page of 15
MO1305-EA © 2013 CASIO COMPUTER CO., LTD. Congratulations upon your selection of this CASIO watch. Applications The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude. Measured values are then shown on the display.
E-8 E-91 Using the Alarm E-91 To enter the Alarm Mode E-92 To set an alarm time E-93 To turn an alarm and the Hourly Time Signal on and off E-94 To stop the alarm E-95 Checking the Current Time in a D.
E-16 • Even when the watch is within range of a transmitter, signal reception may be impossible due to the effects of geographic contours, structures, weather, the time of year, the time of day, radio interference, etc.
E-24 Selecting a Mode • The illustration below shows which buttons you need to press to navigate between modes. • To return to the Timekeeping Mode from any other mode, hold down D for about two seconds.
E-32 Note • For i nfo rma tio n abo ut s ele cti ng a Ho me C it y an d co nfi gu ring t he D ST s et ting , see “ C onfi gurin g Ho me Ci t y Se tt ing s” (pag e E-2 8). • Whi le th e 12-h ou r for mat i s sel ecte d for ti me kee ping , a P (PM) i ndic ator w ill ap pea r for ti me s fro m no on to 11 :59 p.
E-40 Using Bearing Memory Bearing Memory lets you temporarily store and display a direction reading so you can use it as a reference as you take subsequent digital compass readings. The Bearing Memory screen displays the direction angle for the stored reading, along with a pointer that indicates the stored reading.
E-48 Specifying Temperature, Barometric Pressure, and Altitude Display Units Use the procedure below to specify the temperature, barometric pressure, and altitude display units to be used in the Barometer/Thermometer Mode and the Altimeter Mode.
E-56 • Note that time calibration signal reception and power saving (page E-13) are disabled while barometric pressure change indicator display is enabled. • Note that barometric pressure change indicator display cannot be enabled while the watch’s battery is low.
E-64 Advanced Altimeter Mode Operations Use the information in this section to obtain more accurate altimeter readings, especially while mountain climbing or trekking. Using an Altitude Differential Value The Altimeter Mode screen has an altitude differential value that shows the change in altitude from a reference point you specify.
E-72 • Entering the Altimeter Mode starts a new altitude auto reading session, but it does not reset the current ASC and DSC values or change them in any way. This means that the starting ASC and DSC values for a new Altimeter Mode auto reading session are the values that currently are in memory.
E-80 Trek Log Values (Mt.1 to Mt.14) High Altitude Value Low Altitude Value Cumulative Ascent Value Cumulative Descent Value *1 *2 *1: Month and day the displayed value was recorded. *2: Month and day cumulation started. • Holding down A or C scrolls at high speed.
E-88 To measure two fi nishes A C A C C Start Split First runner fi nishes. ( SPLIT appears in the upper part of the display.) Display time of fi rst runner Stop Second runner fi nishes. Split release Display time of second runner Reset Note • The Stopwatch Mode can indicate elapsed time up to 999 hours, 59 minutes, 59.
E-96 To specify standard time or daylight saving time (DST) for a city 1. In the World Time Mode, use A (East) and C (West) to scroll through the available city codes. • Keep s croll ing u ntil t he ci ty c od e who se S ta nda rd Tim e/ D aylig ht Savi ng T ime s et ting y ou wan t to cha nge is d ispl ayed.
E-104 ■ “ERR” appears on the display while I am using a sensor. Subjecting the watch to strong impact can cause sensor malfunction or improper contact of internal circuitry. When this happens, ERR (error) will appear on the display and sensor operations will be disabled.
E-112 Illumination: LED light; Selectable illumination duration (approximately 1.5 seconds or 3 seconds); Auto Light Switch (Full Auto Light operates only in the dark) Other: Battery power indicator; .
An important point after buying a device Casio MO1305-EA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Casio MO1305-EA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Casio MO1305-EA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Casio MO1305-EA you will learn all the available features of the product, as well as information on its operation. The information that you get Casio MO1305-EA will certainly help you make a decision on the purchase.
If you already are a holder of Casio MO1305-EA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Casio MO1305-EA.
However, one of the most important roles played by the user manual is to help in solving problems with Casio MO1305-EA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Casio MO1305-EA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
