Instruction/ maintenance manual of the product 65GxxD Casablanca Fan Company
Go to page of 15
1 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) • The blad es in each pack are m atched f or equal wei ght to assur e smooth f an operati on. If mor e than one f an is being in stalled, be careful n ot to mix blades fr om differen t cartons .
2 Calculation of 32° Use th e tear-off Ceiling Angle T emplate card inserted in th e back of this m anu al, it provi des you with a simple “g o” or “no-g o” for in stalling your f an on a sloped ceiling.
3 V ER RA Z AN O ™ PREP ARA TION INSTR UCTIONS Unpacking: Befor e assembling an d installin g your ceiling f an, rem ove all parts from th e shipping carton s and ch eck them against th e parts listed her e . Befor e discardin g packagin g materi al, be certain that all parts have been rem oved.
4 CROSSBAR MOUNTING BRA CKET INST ALLA TION JOIST CEILING WIRING CROSSBAR MOUNTING BRACKET FLA T W ASHER GREEN GROUND WIRE CEILING F AN APPROVED WIRING BOX RIDGE SIDE DOWN APPROVED OUTLET BOX HARDW ARE Note: After removing the old fi xture , check the outlet box to ensure that it is supported by a joist or beam across its upper surface .
5 V ER RA Z A N O ™ CANOPY INST ALLA TION Step 4. Attach th e canopy to th e crossbar m ountin g brack et with three o f the 8-32 x 2 1 / 2 ” lon g canopy screws an d lock washers pr ovid ed with your Casablanca f an. Han d-tigh ten until sn ug against th e ceiling.
6 HANGING THE F AN Step 5. T o hang th e fan bod y in the can opy , hold th e fan body fi rmly an d insert th e nylon ball in to the can opy open- ing. Rotate f an body un til slot on nylon ball fi ts into pin opposite canopy openin g. CANOPY BAL L SLOT PIN NOTE: The f an weight is 37.
7 V ER RA Z A N O ™ CANOPY HA TCH INST ALLA TION Step 7. T uck th e wires in to the can opy with the wir e nuts poin ted upwards , so that the WHITE an d BLACK wir es are on opposite sid es of th e canopy an d all wires are clear o f the can opy opening.
8 BLADE BLADE ROD BLADE TIP SCREW (2 PER BLADE) BLADE HARD W ARE BLADE TIP Step 10. Remove th e shipping cover fr om each of th e blade r od hold ers on the f an body . Usin g the pr ovid ed Allen wren ch, unscr ew the blad e rod h older scr ew a few turns to assure pr oper installati on of th e blade rod .
9 V ER RA Z A N O ™ INST ALL LIGHT KIT BASE Step 14. Route the m otor wires thr ough the cen ter of th e ligh t kit base . Align th e ligh t kit base onto th e switch housin g using th e tabs of th e switch housin g. Usin g the thr ee switch housin g screws r emoved in Step 13, attach the li ght kit base to th e switch housin g.
10 INST ALL B ULB AND GLASS INST ALL LIGHT KIT BASE Step 15. Attach th e WHITE wire plug fr om the bulb plate to the WHITE wir e plug of th e fan. Th en at- tach the BLA CK wire plug fr om the bulb plate to the BLA CK wire plug o f the f an. The plugs have alignm ent tabs , assure th ese are ali gned —do n ot for ce the conn ection.
11 1. Raise the Fan slid er to incr ease fan speed , lower it to decr ease . 2. For th e fan, f our position s are available: OFF , LOW , MEDIUM, and HI GH. The bottom positi on is OFF . 3. The Li ght sli der is a dimm er , the bottom is OFF; raise to incr ease inten sity of th e ligh t.
12 12 TROUBLESHOO TING Befor e requesting service: Please consult this tr oubleshooting guide befor e contacting your dealer f or assistance . PROBLEM POSSIBLE REMEDIES F AN WILL NOT ST ART Check m ain circuit fuses , circuit break ers, or wall switch position.
13 V ER RA Z A N O ™ A UTHORIZED SER VICE CENTERS STATE/C IT Y ZI P SE RV IC E CE NT ER N AM E PHO N E T YP E COLORADO BOULDER 80306 ENERGETICTECH 303-684-7543 FFS COLORADO SPRINGS 80903 HOME LIGHTING 719-471-3520 WTS DENVER 80229 M.
14 A UTHORIZED SER VICE CENTERS STATE/C IT Y ZI P SER VI C E CEN TE R N AM E PH O NE T Y PE IOW A CARROLL 51401 J & L ELECTRIC INC. 712-792-2444 ISO CEDAR RAPIDS 52404 ACME ELECTRIC COMP ANY 319-3.
15 V ER RA Z A N O ™ STATE/C IT Y ZIP SE RV IC E CE NTE R N AM E PHO N E T YP E OHIO CANTON 44706 APPLIANCE PAR TS CO. 330-453-8077 ISO CLEVELAND 44109 WESTSIDE LIGHTING CTR. 216-459-1970 FFS COLUMBUS 43231 THE LAMP LIGHTER 614-891-7940 FFS COLUMBUS 43235 CERTIFIED SYSTEMS 614-799-0878 IHO DA YTON 45419 LARKIN ELECTRIC CO.
An important point after buying a device Casablanca Fan Company 65GxxD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Casablanca Fan Company 65GxxD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Casablanca Fan Company 65GxxD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Casablanca Fan Company 65GxxD you will learn all the available features of the product, as well as information on its operation. The information that you get Casablanca Fan Company 65GxxD will certainly help you make a decision on the purchase.
If you already are a holder of Casablanca Fan Company 65GxxD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Casablanca Fan Company 65GxxD.
However, one of the most important roles played by the user manual is to help in solving problems with Casablanca Fan Company 65GxxD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Casablanca Fan Company 65GxxD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
