Instruction/ maintenance manual of the product 19th Century Casablanca
Go to page of 17
19 TH C ENTUR Y OWNERS MANUAL.
1 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) • The blad es in each pack are m atched f or equ al weigh t to assur e smooth f an operati on. If mor e than on e fan is being in stalled, be car eful not to mix blades fr om differ ent cartons .
2 Calculation of 32 ° Use th e tear-o ff Ceiling Angle T emplate card inserted in th e back of this m an ual, it provi des you with a simple ‘go’ or ‘no-g o’ for installing your f an on a sloped ceiling.
3 PREP ARA TION INSTRUCTIONS Unpacking: Befor e assembling an d in stalling your ceiling f an, remove all parts fr om the shipping carton s and ch eck them against th e parts listed here . Before discar ding pack aging materi al, be certain that all parts have been rem oved.
4 FAN PREP ARA TION MOT OR COUPLING T APERED THREAD MOT OR WIRES GROUND WIRE Step E. Usin g the pr ovi ded allen wren ch, loosen the allen set screw . Thread th e downr od into th e motor coupling un til it stops turning, this will tak e at least four an d a half full turns.
5 AD APT OR PLA TE INST ALLA TION JOIST CEILING WIRING CROSSBAR MOUNTING BRACKET FLA T W ASHER GREEN GROUND WIRE CEILING F AN APPROVED WIRING BOX RIDGE SIDE DOWN APPROVED OUTLET BOX HARDW ARE Note: After removing the old fixture , check the outlet box to insure that it is supported by a joist or beam across its upper surface .
6 Step 2. Route the outlet bo x wires thr ough the 1 / 2 ″ diam- eter outer hole o f the canopy ad aptor plate . Attach th e crossbar an d canopy ad aptor plate to outlet box with screws provi ded . Step 3. With the lar ge wash er attached, pass th e lag screw through th e center h ole of can opy adaptor plate and scr ew into gui de h ole.
7 HANGING THE F AN Step 5. T o hang the f an body in the can opy , hold the f an body firmly an d insert th e nylon ball in to the canopy open- ing. Rotate f an body un til slot on nylon ball fits into pin opposite canopy openin g.
8 CANOPY COVER DIS ASSEMBLE CANOPY AND MO TOR CO VERS Step 11. T ake th e two pieces o f the canopy cover an d assemble them ar ound the d ownrod as shown. U sing th e four screws r emoved in Step 10, assemble th e canopy cover . Slid e the can opy cover to the ceiling an d secure to th e downr od using th e two pro- vid ed scr ews.
9 A TT ACH BLADE HOLDERS Step 13. Attach th e blades to th e blade hold ers by align- ing th e screw holes o f the h older with th e holes o f th e blade . Attach th e blade h older using th e four blad e screws an d blade wash ers provid ed for each blad e .
10 LIGHT KIT WIRING WIRE NUT NOTE: If y ou do not desir e to install the light kit, see “Optional Switch Housing Cup” installation instructions on P age 11. Step 15. Remove th e wire n uts on th e BLACK and WHITE wir es from th e fan. If n ecessary re- move th e insulati on from th e last 1 / 2 ” of each wire (f an and ligh t fixture).
11 GLASS & BULB INST ALLA TION GLASS SHADE SCREWS Step 18. Loosen the thr ee glass screws f or each fixture so th e en d of th e screws ar e flush with the in side o f the fixtur e .
12 R INTELI•TOUCH ♦ SINGLE W -32 INST ALLA TION The wall con trol in stalls in the same m anner as an ordinary li ght switch, using an e xisting juncti on box an d wirin g. This contr oller is desi gned to sign al the f an microcomputer as well as perform n ormal switching oper ations .
13 INTELI•T OUCH OPERA TION ♦ PO WER + + + + Progr ammed in to every Inteli-T ouch Series f an is an Auto- mati c Demon str ation Progr am. It can be used to fully dem onstr ate and test th e operati on of the f an. T o enter the demonstration progr am: 1.
14 Th e Ligh t-Minder pr ogram automati cally turns OFF the f an moun ted ligh ts after two hours . T o enter the Light-Minder Progr am: 1. T urn th e OFF for at least thr ee seconds. 2. T urn th e ON. 3. Immedi ately operate the button s in the f ollowing sequence: + + + 4.
15 TROUBLESHOO TING Befor e Requesting Service: Please follow this troubleshooting guide bef ore contacting y our dealer f or assistance . Caring for Finishes : For cleanin g, a soft brush or lin t-free cloth should be used to pr event scr atching th e finish.
©C OPYRIGHT 2000 C ASABLANCA F AN C OMPANY • U.S. P ATENT P ENDING P RINTED IN ROC 761 C ORPORATE C ENTER D RIVE • P OMONA , CA 91768 T OLL F REE : 888-CASA-1ST (227-2178) www.
An important point after buying a device Casablanca Casablanca 19th Century (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Casablanca Casablanca 19th Century yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Casablanca Casablanca 19th Century - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Casablanca Casablanca 19th Century you will learn all the available features of the product, as well as information on its operation. The information that you get Casablanca Casablanca 19th Century will certainly help you make a decision on the purchase.
If you already are a holder of Casablanca Casablanca 19th Century, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Casablanca Casablanca 19th Century.
However, one of the most important roles played by the user manual is to help in solving problems with Casablanca Casablanca 19th Century. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Casablanca Casablanca 19th Century along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
