Instruction/ maintenance manual of the product LCD-1900VR Tote Vision
Go to page of 20
.
.
2 Operating Instructions Thank you for purchasing this high - resolution multi - scan color monitor. Please read this guide thoroughly before installation.
3 Safety Precautions This monitor is manufactured and tested on the principle that the user ’ s safety comes first. However, i mproper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy.
4 Care and Maintenance Care l Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to re duce glare. l Put your monitor in a well - ventilated area. Do not place anything heavy on top of your monitor.
5 CHAPTER 1 Introduction BEFORE INSTALLING YO UR MONITOR Read this manual cover to cover. PAY ATTENTION to all WARNING and CAUTIONS DO NOT use computer components not recommend by the manufacture Do not attempt to service the m onitor your self.
6 FACTORY - PRESET MODES Table 1 shows standard video mode setting that has be en pre - adjusted at the factory for accurate video display. These setting are stored in the monitor's memory Table 1. Factory - Preset Modes PC mode Mode Resolution H - Freq.
9 l LCD - 1900V R 19” LCD 8U Rack Display Monit or Overall Dimension (HxWxD): 394.5 x 436 x 62 mm Effective Display area (H/V): 376.32 x 301.56 mm Display colors: 16.7M colors Scan Frequencies: Horizontal 31.47K to 80KHz Vertical 60Hz to 75Hz Number of Pixels: 1280x1024 pixels Pixel pitch : 0.
10 Operations: User Controls On/Off Power Button , +/ - and Up/down keys On Screen Display Auto adjustment, Brightness, contrast color temperature, Hue, Tint, Source select, PIP setup H - position, V .
11 Chapter 2 P RODUCT P ACKAGE Open the shipping carton and check the contents. If any items are missing or da maged, contact your dealer immediately. The package should include the following items l Analog Color TFT LCD Monitor l Accessory Box: 1. VGA cable x 1 2.
12 C ONTROL F UNCTIONS The Monitor control functions are located on the lower center of the front view side. They are shown in the figure below and described in the following paragraphs. The control key description 1. : Power Switch 2. - : Decrement 3.
13 DESCRIPTION 1. : Power switch Use the power switch to turn ON or OFF po wer. We recommend turning your system power on first, then the LCD monitor. 2. - & + : decrement or increment the value The two keys are decrement or increment the value or enter into the sub - menu.
14 CHAPTER 3 A DJUSTING THE MONITOR VGA OSD main screen 1024x768 48.5K 60.2 VER XGA - KDC45 - 5100 Auto Adjustment - Execute + 3.
15 1. Each time, when pressing the menu key, the screen will show as above. You can see the 3 mark that mean s the selected item. Then you can change the setting through + or - .key. 2. Pressing Sel key to move the arrow down or up. If the selected item has many option to choose, press – or + to enter into the sub - menu.
16 Co lor balance: the monitor do the white balance automatically. Intensity R: Adjust the R color intensity, the range is from 0 to 63 Intensity G: Adjust the G color intensity, the range is from 0 t.
17 Geometry setup § W e provide Pixel Clock, Phase, H Position, V Position, OSD H Position, OSD V Position and Txt/Gft option to change. § Pixel Clock: Adjust the viewing screen size. The range is from 0 to 99 Phase: Adjust phase tracking to reduce the display flicker.
18 Note: The PIP function is only valid on video on VGA screen. We can ’ t support video on video screen Speaker volume control § We provide Volume, Bass, Treble, Mute and PIP audio for audio s etup. § Volume: Adjust the speaker volume. The range is from 0 to 32.
19 Chapter 4 VIDEO ADJUSTMENT Video OSD Screen NTSC 15.7K 60.2 VER XGA - KDC45 - 5100 1. Each time, when pressing the menu key, the screen will show as above. You can see th e 3 mark, that means the selected item Then you can change the setting through + or - .
20 § Adjust the screen contrast value. The range is from 0 to 127 Intensity adjustment § Adjust the screen intensity value. The range is from 0 to 255 Tint adjustment § Adjust the scr een Tint value. The range is from 0 to 127 Hue adjustment § Adjust the screen Hue value.
21 Appendix Troubleshooting Procedures This LCD Monitor was pre - adjusted in the factory with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an uns table or unclear display when a new display mode or new VGA card is selected .
An important point after buying a device Tote Vision LCD-1900VR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tote Vision LCD-1900VR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tote Vision LCD-1900VR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tote Vision LCD-1900VR you will learn all the available features of the product, as well as information on its operation. The information that you get Tote Vision LCD-1900VR will certainly help you make a decision on the purchase.
If you already are a holder of Tote Vision LCD-1900VR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tote Vision LCD-1900VR.
However, one of the most important roles played by the user manual is to help in solving problems with Tote Vision LCD-1900VR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tote Vision LCD-1900VR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
