Instruction/ maintenance manual of the product PTS723-3 Smeg
Go to page of 16
Table of Contents 3 1. Precautions for safety and use _________________________ 4 2. Fitting the appliance in the top _________________________ 5 2.1 Fixing to the supporting structure ________________________________________5 3. Electrical connection ________________________________ 7 4.
Precautions for Safety and Use 4 1. Precautions f or safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CY CLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT C ONTAINS BEFORE USING THE HOB.
Instructions for the Installer 5 2. Fitting the appliance in the top The procedures required below must be carried o ut by a skilled builder and/or joiner. The hob can be installed on vari ous materials, including masonry, metal, solid wood and wood finished with plastic laminates, pr ovided the material is heat-resistant (T 90° C).
Instructions for the Installer 6 Fit the insulating gasket provided carefu lly around the outside edge of the hole made in the top as shown below, pressi ng it down with your hands so that its entire surface fits snugly.
Instructions for the Installer 7 3. Electrical connection Check that the power su pply line voltage and size are as speci fied on the nameplate underneath the applian ce's casing.
Instructions for the Installer 8 4. Gas connection If the appliance is installed above an ov er, t he gas hose must be passed around the back of the oven to prevent overheating. The connection to the gas mains ma y be made using a copper pipe or a continuou s-wall steel hose in accordance with the relev ant regul ations.
Instructions for the Installer 9 4.1 Bottled gas connection Use a pressure regulator and ma ke the connection to the gas cylin der in accordance with the relevant regulations. Make sure that the gas supply pressure is as st ated in the table in point "5.
Instructions for the Installer 10 5. Adapting to diff erent types of gas Before carrying out the operations described below, disconnect th e appliance from the electricity supply. The hob is tested with G20 (2H) natural gas at the pressure of 20 mbar.
Instructions for the Installer 11 5.2 Adjusting fo r bottled gas Undo the scr ew A and push the support B fully do wn. Remove the nozzle C with a spanner and fit the suitabl e one following the instructions in the tables referring to the type of gas to be used.
Instructions for the Installer 12 5.5 Adjusting the primary air flow Refers to the gap “ X ” in mm. BURNER G30/G31 30/37 mbar G110 8 mbar G20 20 mbar Semi rapid (1) 10.0 1.5 2.0 Rapid (2) 8.0 1.5 2.5 Ultra-Rapid (3) 12.0 5.0 2.5 To identify the burners on you r hob, refer to the drawings in point “5.
Instructions for the Installer 13 5.9 Hob b urner lay out Burner type 1 Semi rapid 2 Rapid 3 Ultra-Rapid 5.10 Greasing the gas taps Over time, the gas taps may beco me stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled technician.
Instructions for the User 14 6. Description of contr ols 6.1 The fr ont panel All the hob's control and monitori ng devices are placed together on the front panel. KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol .
Instructions for the User 15 7. Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob.
Instructions for the User 16 8. Cleaning and maintenance Before carrying out any operations, disconnect the ap pliance from the electricity supply. 8.1 Cleaning stainless steel To keep the hob in good condition, it must be cleaned regula rly, after each u se, first allowing it to cool.
.
914773119/ B.
An important point after buying a device Smeg PTS723-3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smeg PTS723-3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smeg PTS723-3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smeg PTS723-3 you will learn all the available features of the product, as well as information on its operation. The information that you get Smeg PTS723-3 will certainly help you make a decision on the purchase.
If you already are a holder of Smeg PTS723-3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smeg PTS723-3.
However, one of the most important roles played by the user manual is to help in solving problems with Smeg PTS723-3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smeg PTS723-3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
