Instruction/ maintenance manual of the product VSE-2400 Sanyo
Go to page of 12
VS E-23 00 & VS E-24 00 S E R I ES IN STR U CTI O N MAN UAL C ylindrical En vir onmental Camer a Housings About this manual Before installing and using this unit, please read this manual carefully. Be sure to keep it available for later reference.
2 IMPOR T ANT SAFEGU ARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to.
SAFETY PRECAUTIONS This label may appear on the bottom of the unit due to space limitations. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user t.
CONTENTS 1 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2S ERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3 CARE AND MAINTENANCE . . . . . . . . . . . . . . . .4 4D ESCRIPTION . . . . . . . . . . . .
5 Model Number Preinstalled Heater or Heater/Blower 1 Voltage/Power (V/W) VSE-2300 --- VSE-2300H Heater 24/23 VSE-2300HB Heater/Blower 24/25 VSE-2400 --- VSE-2400H Heater 24/23 VSE-2400HB Heater/Blower 24/25 Model Number Maximum Camera and Lens Weight VSE-2300 2.
6.3 Housing Mounting 1. Use the two 1/4-20 x 0.50-inch screws and 1/4-inch spring washers provided in the hardware kit to mount the housing to a mount or a pan/tilt.
6.5 Camera/Lens Installation 1. Loosen the two screws holding the camera bracket to the base. It is not necessary to remove them completely. See Figure 3 . Figure 3: Removing the Camera Bracket 2. Remove the camera bracket from the base. If you are using the feed-through feature, refer to Section 6.
3. The terminal block provided on /x0 units accepts wire ranging from 20 to 14 AWG or 1.5 mm 2 . The terminal block provided on /x1 units accepts wire ranging from 18 to 12 AWG or 2.5 mm 2 . When using larger wire sizes, splice to a smaller size wire at the terminal block end.
6.8 Lens Wiring WARNING: Only use the cables specified under "INSTALLATION, Cable Requirements" for wiring of the lens. 1. Install the last 1/2-inch NPT fitting into the remaining hole in the rear cap. Zoom lenses can only be installed into VSE-2400 housings.
10 See Detail Cover Rib T op of Base Seal Figure 10: Reinstalling the Cover 3. As the cover nears the rear cap, make sure the captive screws in the back are not blocking the cover from engaging into the rear cap. 4. Screw the two rear captive screws into the housing.
11 THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U. S. TERRITORIES AND PROTECTORATES.
Sanyo Fisher Company Security Video Division 21605 Plummer Street Chatsworth, CA 91311 Tel: (818) 998-7322 Fax: (818) 717-2716 Technical Support: (888) 66SANYO Printed in USA 100 0004 001 SAN 6/02.
An important point after buying a device Sanyo VSE-2400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo VSE-2400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo VSE-2400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo VSE-2400 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo VSE-2400 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo VSE-2400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo VSE-2400.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo VSE-2400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo VSE-2400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
