Instruction/ maintenance manual of the product CM-10GT-SFP Perle Systems
Go to page of 16
Perle 10GT Media Con verter Modul es Installation Gui de C-10GT-SFP CM-10GT-SFP C-10GT-XFPH CM-10GT-XFPH P/N 550033 7-10.
Perle C/CM-10GT Media M odules Insta llation Guide 2 Over v iew This docum ent contains ins tructions neces sary for the ins tallation and operatio n of the Perle C/CM-10GT Media Converter m odules. These m odels are used in conjunction with a Perle Media Converter chas sis.
Perle C/CM-10GT Media M odules Insta llation Guide 3 Getting t o know your C/ CM-10GT Media Con verter Your C/CM-1 0GT Media C onverter pack age consists of the following item s: • C/CM-10GT module with one tr ansceiver port ( SFP+ or XF P) and one RJ -45 (copper) po rt.
Perle C/CM-10GT Media M odules Insta llation Guide 4 Installation The default s witch setting ( all switches in the U P position) will work for m ost installations. The Auto-Jumper is s et to Auto f or Ethernet Auto detectio n. These are the s teps require d to configure the Perle C/CM-10G T module.
Perle C/CM-10GT Media M odules Insta llation Guide 5 DIP Switch Settings The DIP s witches are locat ed on the m odule. Note: Switc h changes mad e when the modu le is power ed up take effect immed iately and will result in a link r eset on both ports .
Perle C/CM-10GT Media M odules Insta llation Guide 6 Test Function (Sw itch 2 – Test Mode) Switch Posit ion Type Up (defau lt) Built In Link Test (BILT ) Down Loopback Built In Link T est: Set Swi tch 2 to the Up position for the C/C M- 10GT m edia converter m odule to initiate the Built In Link Test on port 1.
Perle C/CM-10GT Media M odules Insta llation Guide 7 Sequence of E vents 1. The Local C/ CM-10GT m e dia converter m odule send s the Rem ote C/CM-10GT m edia converter m odule a signal to go into test m ode. 2. The Rem ote C/CM-10GT media con verter module tur ns on test m ode.
Perle C/CM-10GT Media M odules Insta llation Guide 8 Fiber Faul t A lert Sample Confi g Media Converter Module A Configurati on Link Mode–S tandard Mode Fiber Fault A lert Media Converter Module B Configuration Link Mode–S mart Link Pas s through Mode Fiber Fault A lert Sequence of Events 1.
Perle C/CM-10GT Media M odules Insta llation Guide 9 EEE (Ene rgy Efficient Ethernet) Switch Posit ion Mode Up (defau lt) Enabled Down Disabled Enabled: W hen enabled, t he media convert er will auto negot iate this capabili ty with the attached EEE com pli ant dev ices/servers.
Perle C/CM-10GT Media M odules Insta llation Guide 10 AUTO-Config Jump er (CM mod els only) The Auto-Co nfig jumper is located on the outer edge, at the midpoint of the module. Jum per the top and m iddle pin to se lect Auto m ode. Jumper the m iddle and bottom pin to select SW mode.
Perle C/CM-10GT Media M odules Insta llation Guide 11 Operation Status LED The Perle C/C M 10GT Med ia converters m odules have three status LEDs located on the faceplate of the m odule. PWR - Pow er/Test Green On: P ower is on an d the module is in normal oper ation mode.
Perle C/CM-10GT Media M odules Insta llation Guide 12 LK1- Port 1 A cti vity On: Fiber l ink present. Blinking quic kly : Fiber link present and receivin g data. Blinking slowl y : The fiber link has been tak en down as a result of Smart Link Pass-Through.
Perle C/CM-10GT Media M odules Insta llation Guide 13 T roublesh ooting General Ensure that the SFP+ or X FP module is insert ed correctl y into the transc eiver port. Ensure that the copper cabl ing (RJ-45) m eets Ethernet copper cabling requ irements.
Perle C/CM-10GT Media M odules Insta llation Guide 14 Loopback Test This m ode is not used in conj unction with BILT . 1. If either m edia converter m odule is not a Perle 10GT m odule then you need to set loopbac k mode on one of the media converter m odules.
Perle C/CM-10GT Media M odules Insta llation Guide 15 Technical S pecifications Power Input/C onsumption 9-30VDC SFP+ 1.1A Max, 0.8 A at 12VDC Operating T emperature 0° C -50° C (32° F - 1 22° F) .
Perle C/CM-10GT Media M odules Insta llation Guide 16 Complian ce Informati on FCC This product has been found to comply w ith the limits for a Class A d igital device, pursuant to Part 15 of the FCC rules.
An important point after buying a device Perle Systems CM-10GT-SFP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Perle Systems CM-10GT-SFP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Perle Systems CM-10GT-SFP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Perle Systems CM-10GT-SFP you will learn all the available features of the product, as well as information on its operation. The information that you get Perle Systems CM-10GT-SFP will certainly help you make a decision on the purchase.
If you already are a holder of Perle Systems CM-10GT-SFP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Perle Systems CM-10GT-SFP.
However, one of the most important roles played by the user manual is to help in solving problems with Perle Systems CM-10GT-SFP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Perle Systems CM-10GT-SFP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
