Instruction/ maintenance manual of the product SEDONA Jacuzzi
Go to page of 20
SEDONA ™ Steam & Shower Base INST ALLA TION/OPERA TING INSTRUCTIONS.
IMPORT ANT SAFETY INFORMA TION READ ALL INSTALLATION INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steam system can raise excessively the internal human body temperature and impair the body’s ability to regulate its internal temperature (hyperthermia).
CONTENTS Specifications _________________________________________________________________________ 2 Roughing-in Reference _________________________________________________________________ 2 Framing an.
*SteamPro supplied with NEMA 6-50P plug. NEMA 6-50R receptacle required. Product specifications are subject to change without notice. SPECIFICATIONS DIMENSIONS 60" (1524 mm) L 32" ( 813 mm) W 18-5/8" ( 473 mm) H TOTAL WEIGHT/ FLOOR LOADING 310 lbs (141 kg) /23 lb/sq.
10-1/2" x 5" DRAIN CUT -OUT 15-3/8" 33-1/4" 60-1/4" FRONT OF DOUBLE STUDS SUB-FLOOR 90º 90º MINIMUM 6" FROM FINISHED CEILING OR BOTTOM OF OPTIONAL DOME TO TEMPERA TURE .
4 Drain Down Locations There are several locations (left hand unit shown) where the optional automatic valve may be located when connecting to a drain line as shown in illustration. Right hand unit is mirror image. Exact location to be determined by installer.
5 Minerals in the water or poor water quality can shorten the life of the steam generator or cause erratic operation if the tank is not drained regularly. Drain the tank frequently. Jacuzzi Whirlpool Bath also strongly recommends purchasing and installing the optional automatic drain down valve.
6 SHUT OFF V AL VE WA TER SUPPL Y (3/8" COPPER TUBING) W ater Supply Consult local authorities for plumbing code require- ments in your area. Connect house cold water supply to steam generator supply tubing. IMPORTANT: Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings and piping or drain systems.
7 Controller Mounting Finished Wall Mounting The low voltage control can be mounted directly to a finished wall either inside or outside the steam room. Using a 2" hole saw, drill a hole in the finished wall where the control is to be mounted (the control cable should already be roughed-in to this location).
8 W ALL PROBE MUST POINT DOWNW ARD 7/8" HOLE OPTIONAL TRIM RING SILICONE SEALANT PIGT AIL Flange Mounting After base is in position secure flange to studs with screws provided.
9 Service Access Service access is through the removable panel. To remove panel, grab the middle of the panel and bow outwards till clips disengage. SERVICE ACCESS P ANEL GRAB P ANEL IN MIDDLE AND BOW.
10 REMOVE SCREWS MOUNTING BRACKET SHIPPING RESTRAINT WA TER SUPPL Y SHUT OFF V AL VE TO STEAM HEAD DRAIN DOWN Maintenance of the SteamPro Unit Maintenance of the SteamPro includes flushing and visually inspecting for water leaks. To remove the unit remove the access panel.
11 T roubleshooting There are no user serviceable parts in the Generator. All repair should be performed by a qualified service person. For additional assistance or the factory authorized service person nearest you call the Service Department at 1-800- 363-0251 (This number is only for service for the steam generator.
12 T roubleshooting.
13 W iring Diagram.
14 ©2002 Jacuzzi Whirlpool Bath T87100B 2/04 Jacuzzi Whirlpool Bath National Headquarters P.O. Drawer J, Walnut Creek, CA 94596 (925) 938-7070 Service Support: Call (800) 288-4002 Jacuzzi Whirlpool Shower base has obtained applicable code (standards) listings generally available on a national basis for products of this type.
Jacuzzi Whirlpool Bath C/O AMEREC P.O. Box 2258 Woodinville WA, 98072 Jacuzzi Whirlpool Bath, warrants that its Steam Generators (warranted products) are free of manufacturing defects both as to workm.
6. Procedure. Requests for repair or replacement, a return authorization number, or warranty information should be directed to AMEREC by calling toll-free 1-800-363-0251 or by writing to AMEREC, 17683 128th Place N.
Jacuzzi Whirlpool Bath Limited W arranty Builder Gr oup Bath Pr oduct Jacuzzi Whirlpool Bath P .O. Drawer J W alnut Creek, CA 94596-9885 WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) of.
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.
An important point after buying a device Jacuzzi SEDONA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jacuzzi SEDONA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jacuzzi SEDONA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jacuzzi SEDONA you will learn all the available features of the product, as well as information on its operation. The information that you get Jacuzzi SEDONA will certainly help you make a decision on the purchase.
If you already are a holder of Jacuzzi SEDONA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jacuzzi SEDONA.
However, one of the most important roles played by the user manual is to help in solving problems with Jacuzzi SEDONA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jacuzzi SEDONA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
