Instruction/ maintenance manual of the product 1171880 Invacare
Go to page of 96
User Manual This manual MUST be given to the us er of the product. BEFORE using this product, read this manual and save for future reference. EN ® Invacare ® Top End Reveal ™ Wheelchair.
2 Part No 1171880 © 2011 Invacare Corporation. All rights reserved. Republic ation, duplication or modification in whole or in part is prohibited wit hout prior written permission from Invacare. Trademarks are identified by ™ and ®. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted.
CONTENTS Part No 1171880 3 Invacare ® Top End Reveal ™ Whe elchair 1 GENERAL 6 Symbols .............. .......................... .......................... ......................... ..................... ............................................
CONTENTS Invacare ® Top End Reveal ™ Wheelchair 4 Part No 1171880 6 FOOTREST 32 Adjusting/Replacing Standard Footres t ........... ......................... .......................... ..................... ....... ............................. ....
CONTENTS Part No 1171880 5 Invacare ® Top End Reveal ™ Whe elchair Replacing Quad-Release Axles.................... .......................... .......................... .................... ....... ................... .......................... ..
1 GENERAL Invacare ® Top End Reveal ™ Wheelchair 6 Part No 1171880 1 General 1.1 Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which co uld result in personal injury or property damage. See the information below for definitions of the signal words.
1 GENERAL Part No 1171880 7 Invacare ® Top End Reveal ™ W heelchair 1.2 Lim ited Warranty PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FED ERAL LAW APPLICABLE TO PROD UCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended onl y to the original purchaser/user of our products.
2 SAFETY Invacare ® Top End Reveal ™ Wheelchair 8 Part No 1171880 2 Safety The safety section contains important i nformation for the safe operation an d use of this product.
2 SAFETY Part No 1171880 9 Invacare ® Top End Reveal ™ W heelchair WARNING Wheelchair Tie Down Restraints Invacare recommends that wheelchair users not be transported in ve hicles of any kind while in w heelchairs.
2 SAFETY Invacare ® Top End Reveal ™ Wheelchair 10 Part No 1171880 WARNING Repair and Service Informati on Unless otherwise noted, al l service and adjustments should be performed while the wheelchair is unoccupied.
2 SAFETY Part No 1171880 11 Invacare ® Top End Reveal ™ Whe elchair WARNING Check all Allen scre ws that secure the foo trest/raised footrest system to the wheelchair frame before us ing the wheelchair, especially if engaging in any contact sport.
3 OVERVIEW Invacare ® Top End Reveal ™ Wheelchair 12 Part No 1171880 3 Overview 3.1 L abel Locations Detent balls should extend bey ond the diameter of the axle bushing for a positive loc k. Keep detent balls clean. W ARNING P/N 1026960 Re v D WE I GHT C AP A CI T Y 250 LB S .
3 OVERVIEW Part No 1171880 13 Invacare ® Top End Reveal ™ Whe elchair 3.2 Component Id entification Seat Upholstery Back Upholstery Rear Whee l Rear Wheel Axle Wheel Lock Wheelchair Frame Front Cas.
3 OVERVIEW Invacare ® Top End Reveal ™ Wheelchair 14 Part No 1171880 3.3 T ypical Product Parameters All specifications are approximate. REVEAL RVL MODEL NUMBER: RVL FRONT FRAME: Non Tapered fr.
3 OVERVIEW Part No 1171880 15 Invacare ® Top End Reveal ™ Whe elchair BACK UPHOLSTERY: U850 (Ballistic Black) - Adjustable Tension by Straps Breathable Mesh (Grey) Adjustable Tension by Straps Fold.
3 OVERVIEW Invacare ® Top End Reveal ™ Wheelchair 16 Part No 1171880 *WEIGHT: 19.71 lbs SHIPPING WEIGHT: 30 lbs WEIGHT LIMITATION: 250 lbs *16 x 16 w/ Spinergy wheels, Primo hi-pressure tires, screw - on seat upholstery, mesh ba ck upholstery w/ adjustable tension & 4” semi-pneumatic cast ers are included in the weight.
4 SAFETY/HANDLING OF WHEELCHAIRS Part No 1171880 17 Invacare ® Top End Reveal ™ Whe elchair 4 Safety/Handling of Wheelchairs 4.1 Safety/Handling of Wheelchairs “Safety and Handling” of the wheelchair requi res the close attention of th e wheelchair user as well as the assistant.
4 SAFETY/HANDLING OF WHEELCHAIRS Invacare ® Top End Reveal ™ Wheelchair 18 Part No 1171880 To assure stability and proper operation of your wheelchair, you MUS T at all times maintain prope r balance.
4 SAFETY/HANDLING OF WHEELCHAIRS Part No 1171880 19 Invacare ® Top End Reveal ™ Whe elchair • Lengthening the wheelba se will increase the st ability and maintain standard maneuverabil ity of wheelchair.
4 SAFETY/HANDLING OF WHEELCHAIRS Invacare ® Top End Reveal ™ Wheelchair 20 Part No 1171880 Reaching, Leaning - Backwards Position wheelchair as c lose as possible to the desired object . Point front casters forward to create the longest possible whee lbase.
4 SAFETY/HANDLING OF WHEELCHAIRS Part No 1171880 21 Invacare ® Top End Reveal ™ Whe elchair Also, be aware of any removabl e (detachable) parts. These MUST NEVER be used to move the wheelchair or as lifting supports, as they may be inadvertently releas ed, resulting in possible i njury to the user and/or assistant(s).
4 SAFETY/HANDLING OF WHEELCHAIRS Invacare ® Top End Reveal ™ Wheelchair 22 Part No 1171880 Roll the wheelch air backward and slowly lower the wheelchair in one continuous movement. DO NOT let the wheelchair drop the last few inches to the ground. This co uld result in injury t o the occupant.
4 SAFETY/HANDLING OF WHEELCHAIRS Part No 1171880 23 Invacare ® Top End Reveal ™ Whe elchair 5. The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has be en rolled away from th e stairway. 6. If necessary, rotate the anti-tippers so the wheels are facing down.
4 SAFETY/HANDLING OF WHEELCHAIRS Invacare ® Top End Reveal ™ Wheelchair 24 Part No 1171880 4.7 Escalators 4.8 Trans ferring To and From Other Seats Position the wheelchair as close as possible along side the seat to which you are transferring, with the front casters parallel to it.
5 SAFETY INSPECTION Part No 1171880 25 Invacare ® Top End Reveal ™ Whe elchair 5 Safety Inspection 5.1 Safety Inspection Checklist Initial adjustments should be made to suit your personal body structure an d preference.
5 SAFETY INSPECTION Invacare ® Top End Reveal ™ Wheelchair 26 Part No 1171880 ❑ Ensure quick release axles and camber inserts are clean. ❑ Ensure camber bar mounting clamps are securely tightened. ❑ Ensure quick/quad release axles lock properly.
5 SAFETY INSPECTION Part No 1171880 27 Invacare ® Top End Reveal ™ Whe elchair ❑ Inspect wheel/fork assembly for proper t ension by spi nning caste r; caster should come to a gradual stop. ❑ If caster flutter o ccurs, tighten fork stem nut to set n eeded drag.
5 SAFETY INSPECTION Invacare ® Top End Reveal ™ Wheelchair 28 Part No 1171880 ❑ Ensure wheel bearings are cl ean and free of moisture . ❑ Check that all labels are pres ent and legible.
5 SAFETY INSPECTION Part No 1171880 29 Invacare ® Top End Reveal ™ Whe elchair 5.3 Maintenance Maintenance Safety Precautions Suggested Maintenance Procedures 1. Before using your wheelchair, make sure all nuts and bolts are tight. 2. Check all parts for damage or wear and replace.
5 SAFETY INSPECTION Invacare ® Top End Reveal ™ Wheelchair 30 Part No 1171880 5. Clean quick-release axles and camber inserts once a week with a Teflon® lubricant. 6. Periodically adjust wheel lo cks in correlation to tire wear. Refer to Replacing/Adjusting the Wheel Locks on page 63.
5 SAFETY INSPECTION Part No 1171880 31 Invacare ® Top End Reveal ™ Whe elchair Replacing/Repairing Rear Wheel Tire/Tube Replacing/Repairing Caster Tire/Tube WARNING Replacement of solid urethane tires is not recommended. If the solid urethane tire needs repaired, Invacare recommends replacing the complete wheel assembly.
6 FOOTREST Invacare ® Top End Reveal ™ Wheelchair 32 Part No 1171880 6 Footrest 6.1 A djusting/Replacing Standard Footrest Adjusting the Footrest 1. Remove the two mounting screws and locknuts that secure the footrest to the wheelchair frame. 2. Adjust footre st to desired height.
6 FOOTREST Part No 1171880 33 Invacare ® Top End Reveal ™ Whe elchair Replacing the Footrest 1. Remove the two mo unting screws and locknuts that se cure the footrest to the wheelchair frame. 2. Remove existing footrest. 3. Install new footrest. 4.
6 FOOTREST Invacare ® Top End Reveal ™ Wheelchair 34 Part No 1171880 2. Slide the existing footrest tube s out of the wheelc hair frame and install ne w footrest by reversing this s tep. 3. Position the new fo otrest to a determined height. 4. Tighten the mounting screws and locknuts to secure the footrest to the wheelchair frame.
6 FOOTREST Part No 1171880 35 Invacare ® Top End Reveal ™ Whe elchair FIGURE 2 Replacing/Adju sting Optional Adjustable Angle Footrest Footrest Tube Additional Mounting Positions Footplate Lock.
7 ARMS Invacare ® Top End Reveal ™ Wheelchair 36 Part No 1171880 7 Arms 7.1 Installing the Swingaway Padded Armrest Socket 1. Remove the back. Refer to Remo ving/Installing the Back Frame on page 59. 2. Remove the split ring of the back release cord from the plunger pin in the back stop insert.
7 ARMS Part No 1171880 37 Invacare ® Top End Reveal ™ Whe elchair FIGURE 1 Disconnect Back Release Cord 5. Remove the rear seat upholstery mounting screw and short mounting screw (FIGURE 2). 6. Remove the back stop insert from seat rail (FIGURE 2).
7 ARMS Invacare ® Top End Reveal ™ Wheelchair 38 Part No 1171880 FIGURE 3 Asse mble Back Stop Insert and Arm Socket Right Side Armrest Socket Left Side Armrest Socket Mounting Screws Washers Ba.
7 ARMS Part No 1171880 39 Invacare ® Top End Reveal ™ Whe elchair 10. Install the back stop in sert/arm socket assembly into the seat rail. 11. Install short mounting sc rew through seat rail and into back stop insert/arm socket assembly. DO NOT tighten.
7 ARMS Invacare ® Top End Reveal ™ Wheelchair 40 Part No 1171880 13. Install the plunger pin into the back stop insert (FIGURE 5). 14. Secure the split ring of the back release cord onto the plunger pin in the back stop insert (FIGURE 5). 15.
7 ARMS Part No 1171880 41 Invacare ® Top End Reveal ™ Whe elchair 7.2 Installing/Removing/Adjusting the Sw ingaway Padded Armrest Installing 1. Tighten mounting bolt and locknut in desired mounting hole. 2. Insert swing away padded armre s t into armrest socket so that notch fits around mounting bolt.
7 ARMS Invacare ® Top End Reveal ™ Wheelchair 42 Part No 1171880 7.3 R emoving/Installing and Adjus ting T-Arms Removing/Installing T-Arms 1. Align the T-arm with the socke t in the T-arm bracket on the wheelchair frame. 2. Slide the T-arm into the T-arm bracket until the height adjustment screw rests on the top o n the T-arm bracket.
8 BACK Part No 1171880 43 Invacare ® Top End Reveal ™ Whe elchair 8 Back 8.1 Unfold ing/Folding the Back 1. To fold the back, pull up on the back release cord and push the back toward the seat of the wheelchair (Detai l “A”).
8 BACK Invacare ® Top End Reveal ™ Wheelchair 44 Part No 1171880 FIGURE 1 Unfoldin g/Folding the Back Back Release Cord Back Back Back Release Cord Seat Seat DETAIL “A” - FOLDING THE BACK D.
8 BACK Part No 1171880 45 Invacare ® Top End Reveal ™ Whe elchair 8.2 Back Angle Adjustment 1. Fold down the back. Refer to Unfo lding/Folding the Back on page 43. 2. Loosen the jam n ut on the placement sc rew locate d at the bottom of the back cane (Detail “A”).
8 BACK Invacare ® Top End Reveal ™ Wheelchair 46 Part No 1171880 8. Repeat STEPS 2-6 for remaining back cane. 9. Unfold the back until the plunger pins lock into the mounting holes in the adjustment square. 10. Unthread the placement scre w until head of screw rests on seat rail (Detail “D”).
8 BACK Part No 1171880 47 Invacare ® Top End Reveal ™ Whe elchair FIGURE 2 Back Angle Adjustment Back Cane Jam Nut Placement Screw DETAIL “A” Adjustment Square Mounting screw secures the ad.
8 BACK Invacare ® Top End Reveal ™ Wheelchair 48 Part No 1171880 FIGURE 3 Back An gle Adjustment - Adjustment Square Position DESIRED SEAT ANGLE ADJUSTMENT SQUARE POSITION NUMERICAL GRAPHICAL -.
8 BACK Part No 1171880 49 Invacare ® Top End Reveal ™ Whe elchair FIGURE 4 Back Angle Adjustment - Adjustment Square Position 0° +4° 83° Back Cane Seat Rail OPTION 1 OPTION 2 Back Angle Plat.
8 BACK Invacare ® Top End Reveal ™ Wheelchair 50 Part No 1171880 FIGURE 5 Back An gle Adjustment - Adjustment Square Position 8.3 A djustable Tension Back Upholstery The Back Upholstery Cover +8° WARNING ALWAYS perform these procedures in the pr esence of an assistant.
8 BACK Part No 1171880 51 Invacare ® Top End Reveal ™ Whe elchair Adjusting the Back Tension To adjust the back tension, perform the following 1. Lift back upholstery cover up and flip over toward front of wheelchair 2. Tight en or loo sen the adj uster f astenin g straps.
8 BACK Invacare ® Top End Reveal ™ Wheelchair 52 Part No 1171880 Removing/Installing the Back Uph olstery Cover, Adju stable Tension Back Upholstery and Lumbar Strap Removing the Back Upholstery Cover 1.
8 BACK Part No 1171880 53 Invacare ® Top End Reveal ™ Whe elchair 4. Return back to upright position. Refer to Unfolding/Foldi ng the Back on page 43. 5. Install the back upholste ry. Refer to Removing the Back Upholstery Cover Installing the Adjustable Tension Back Up holstery 1.
8 BACK Invacare ® Top End Reveal ™ Wheelchair 54 Part No 1171880 FIGURE 7 Removing/Instal ling the Back Upholstery Cover, Adju stable Tension Back Upholstery and Lumbar Strap DETAIL “A” DET.
8 BACK Part No 1171880 55 Invacare ® Top End Reveal ™ Whe elchair FIGURE 8 Removing/Installing the Back Upholstery Cover, Adju stable Tensio n Back Upholstery and Lumbar Strap DETAIL “E” Fa.
8 BACK Invacare ® Top End Reveal ™ Wheelchair 56 Part No 1171880 8.4 R emoving/Installing Foldover Bac k Upholstery Removing Foldover Back Upholstery 1. Unfasten the two fastening flaps that secure the bottom of the existing back upholstery to the back canes.
8 BACK Part No 1171880 57 Invacare ® Top End Reveal ™ Whe elchair 8.5 Back Height Adjustment 1. Remove the back upholstery cover and adjusta ble tension back upholstery. Refer to Re moving/Installing the Back Upholstery Cov er, Adjusta ble Tension Back Upholstery and Lumbar Strap on page 52.
8 BACK Invacare ® Top End Reveal ™ Wheelchair 58 Part No 1171880 FIGURE 10 Back Height Adju stment Back Cane Insert Hole Number 4 3 2 1 5 Adjustment Pin Back Cane.
8 BACK Part No 1171880 59 Invacare ® Top End Reveal ™ Whe elchair 8.6 Removing/Installing the Back Frame Removing 1. Fold the back down. Refer to Unfo lding/Folding the Back on page 43. 2. Loosen rear seat upholstery screw and short mounting screw but DO NOT remove.
9 SEAT Invacare ® Top End Reveal ™ Wheelchair 60 Part No 1171880 9 Seat 9.1 Replacing Seat Upholstery 1. Remove the seat cu shion from the wheelchair.
9 SEAT Part No 1171880 61 Invacare ® Top End Reveal ™ Whe elchair 9.2 Changing Seat Angle/Ch anging Rear Seat Hei ght 1. Fold the back down. Refer to Unfo lding/Folding the Back on page 43. 2. Remove the rear wheels. Refer to Removing/Installing Rear Wheels on page 66.
9 SEAT Invacare ® Top End Reveal ™ Wheelchair 62 Part No 1171880 FIGURE 2 Changing Seat Angle/Changing Rear Seat Height Camber Tube Clamp Assembly Height Adjustment Bar Height Adjustment Bar Wh.
10 WHEEL LOCKS Part No 1171880 63 Invacare ® Top End Reveal ™ Whe elchair 10 Wheel Locks 10.1 Replacing/Adjusting the Wheel Locks Replacing the Wheel Lock 1. Loosen the two mount ing screws and remove the existi ng wheel lock from the w heelchair. 2.
10 WHEEL LOCKS Invacare ® Top End Reveal ™ Wheelchair 64 Part No 1171880 5. Repeat the above procedures until the wheel locks hold the wheelchair. FIGURE 1 Replacing/Adj usting the Wheel Locks 10.2 Changing Wheel Lock Handle Position 1. Loosen, but DO NOT remove, the rear handle mounting screw.
10 WHEEL LOCKS Part No 1171880 65 Invacare ® Top End Reveal ™ Whe elchair 10.3 Converting Wheel Lock From Push-to-Lock to Pull-to-Lock or Pull-to-Lock to Push-to-Lock Converting From P ush-to-Lock to Pull- to-Lock 1. Remove set sc rew from the lower s top position (Detail “A”) .
11 WHEELS Invacare ® Top End Reveal ™ Wheelchair 66 Part No 1171880 11 Wheels 11.1 Removing/Installing Rear Wh eels 1. Perform one of the following: • Quick-Release - Push in the tip of the quick-release axle and pull axle and wheel away from the wheelchair.
11 WHEELS Part No 1171880 67 Invacare ® Top End Reveal ™ Whe elchair FIGURE 1 Removing/Install ing Rear Wheels 11.2 Adjusting Quick-Release Axles 1. Remove rear whee l and quick-release axle from the wheelchair. Refer to Removing/Installing Rear Wheels on page 66.
11 WHEELS Invacare ® Top End Reveal ™ Wheelchair 68 Part No 1171880 11.3 Replacing Quad-Release Axles 1. Remove rear wheel and the existing quick-release axl e from the wheelchair. Refer to Removing/Instal ling Rear Wheels on page 66. 2. Remove existing quic k-release axle from rear wh eel.
11 WHEELS Part No 1171880 69 Invacare ® Top End Reveal ™ Whe elchair 4. Tighten the locking screw. 5. Reinstall the rear wheel and quad-release axle onto the wheelchair.
11 WHEELS Invacare ® Top End Reveal ™ Wheelchair 70 Part No 1171880 11.5 Handrim Replacement 1. Remove the rear wheel from the wheelchair. Refer to Removing/Installing Rear Wheels on page 66. 2. Remove all air from the tube by pressing down on the pin in the ce nter of the valve stem.
11 WHEELS Part No 1171880 71 Invacare ® Top End Reveal ™ Whe elchair 11.6 Adjusting Wheelbase Length [Adjusting Center of Gravity (COG)] Determining Wheelbase Length 1. Measure the distance between the center of the front caster and the center of the rear w heel to determine the wheelbase length.
11 WHEELS Invacare ® Top End Reveal ™ Wheelchair 72 Part No 1171880 Moving the height adjustment ba r forward or back on the frame. ‘ 1. Fold the back down. Refer to Unfolding/Folding the Back on page 43. 2. Remove the rear wheels. Refer to Rem oving/Installing Rear Wheels on page 66.
11 WHEELS Part No 1171880 73 Invacare ® Top End Reveal ™ Whe elchair FIGURE 7 Moving the height adjustment bar forward o r back on the frame. ‘ Mounting Screws Mounting Screws Locknuts Height.
11 WHEELS Invacare ® Top End Reveal ™ Wheelchair 74 Part No 1171880 11.7 Adjusting Wheelbase Width 1. Remove the rear wheels. Refer to Rem oving/Installing Rear Wheels on page 66. 2. Loosen the axle nut and rotate axle busing to increase/dec rease the wheelbase w idth.
11 WHEELS Part No 1171880 75 Invacare ® Top End Reveal ™ Whe elchair 11.8 Removing/Installing the Camber Tube Removing the Camber Tube 1. Remove the rear wheels. Refer to Removing/Installing Rear Wheels on page 66. 2. Loosen the two sock et head clamp screws se curi ng camber tube to the tw o camber tube clamps.
11 WHEELS Invacare ® Top End Reveal ™ Wheelchair 76 Part No 1171880 FIGURE 9 Removing/Installing the Camber Tube Camber Tube Clamp Camber Tube DETAIL “A” - CORRECT ORIENTATION FOR EACH CAMB.
11 WHEELS Part No 1171880 77 Invacare ® Top End Reveal ™ Whe elchair 11.9 Adjusting the Camber Tube 1. Loosen, but DO NOT remove, the so cket head clamp screws in the camber tube clamps (Detail “A”). 2. Using an "L" square, ro tate the axle tube until the flat edge of the camber tube is at a 90° angle w ith the ground/floor.
11 WHEELS Invacare ® Top End Reveal ™ Wheelchair 78 Part No 1171880 11.10 Determining/Setting Toe In/Toe Out 1. Inflate all pneumatic tires to recommended tire pressures (listed on the sidewall of the tire).
11 WHEELS Part No 1171880 79 Invacare ® Top End Reveal ™ Whe elchair FIGURE 11 Determining/Sett ing Toe In/Toe Out Front of Wheelchair Centerlines of Rear Wheels Front of Wheelchair Top View of.
12 CASTER Invacare ® Top End Reveal ™ Wheelchair 80 Part No 1171880 12 Caster 12.1 Adjusting Fork Tension 1. To properly tighten forks and guard against flutter, perform the following check on both forks: A. Tip back the wheelchair to floor. B. Pivot both forks and casters to t op of their arc simultaneously.
12 CASTER Part No 1171880 81 Invacare ® Top End Reveal ™ Whe elchair FIGURE 1 Adjusting Fork Tension Fork Locknut Caster DETAIL “A” STANDARD FORK DETAIL “B” - ONE SIDED FORK.
12 CASTER Invacare ® Top End Reveal ™ Wheelchair 82 Part No 1171880 12.2 Removing/Installing /Repositioning the Caster Assemblies Standard Forks Removing Front Cas ter 1. Remove the mounting bolt, axle spacers and locknut that secure the front caster to the fork.
12 CASTER Part No 1171880 83 Invacare ® Top End Reveal ™ Whe elchair One Sided Fork Removing the Ca ster 1. Remove the button head screw t hat secure the caster to the fork. Installing the Caster 1. Secure caster to one sided fork with button head screw.
12 CASTER Invacare ® Top End Reveal ™ Wheelchair 84 Part No 1171880 Installing Fork Assembly 1. Perform one of the following: • Standard Forks - Using a locknut, secure the spec tre and fork to the fork stem (Detai l “A”). • One Sided Fork (Detail “B”) a.
12 CASTER Part No 1171880 85 Invacare ® Top End Reveal ™ Whe elchair 12.4 Repositioning the Front Caster Housings 1. Remove the top moun ting screw, belleville washer an d round adjustment nut and base tha t secures the caster housing to the fro nt frame.
12 CASTER Invacare ® Top End Reveal ™ Wheelchair 86 Part No 1171880 FIGURE 5 Repositioning the Front Caster Housings 12.5 Caster Housing Angle Adjustment Small Angle Adjustments 1. If necessary, loosen the top mounting screw (Detail “A”). 2.
12 CASTER Part No 1171880 87 Invacare ® Top End Reveal ™ Whe elchair 3. Rotate the round adjustment nut clockwise/ counterclockwise until edge of fork is flus h with “L” square and is 90° to ground/f loor (Detail “B”). 4. Tighten the top and bottom mounting screws se curely (Detail ”A”).
12 CASTER Invacare ® Top End Reveal ™ Wheelchair 88 Part No 1171880 FIGURE 6 Caster Housing Angle Adjust ment DETAIL “C” Top Mounting Screw Front Frame Round Adjustme nt Nut Square Adjustme.
13 ANTI-TIPPER Part No 1171880 89 Invacare ® Top End Reveal ™ Whe elchair 13 Anti-Tipper 13.1 Adjusting/Replacing Anti-tipper WARNING After ANY adjustments, repair or servic e and BEFORE use, make sure all attach ing hardware is tightened securely - otherwise injury or damage may occur.
13 ANTI-TIPPER Invacare ® Top End Reveal ™ Wheelchair 90 Part No 1171880 Adjusting Anti-tipper 1. Press in the lock button th at secures the anti-tipper wheel assembly to the anti-tipper bar. 2. Adjust the height of the anti-tipper wheels to betw een 1-1/2 and 2-inches of t he ground/floor.
13 ANTI-TIPPER Part No 1171880 91 Invacare ® Top End Reveal ™ Whe elchair 6. If necessary, adjust the height of the anti-tippers. Refer to Adjusting Anti-tipper on page 90.
13 ANTI-TIPPER Invacare ® Top End Reveal ™ Wheelchair 92 Part No 1171880 FIGURE 2 Adjusting/Replacing A nti-tipper Mounting Hole (Hidden) Release Buttons ANTI-TIPPERS BRACKET SE TTING FOR HIGHE.
13 ANTI-TIPPER Part No 1171880 93 Invacare ® Top End Reveal ™ Whe elchair 13.2 Reversing Anti-tippe r Brac ket Orientat ion 1. Press in the release buttons and remove th e anti-tipper from the anti-tipper bracket. 2. Loosen, but DO NOT remove, anti-tipper moun ting screws.
13 ANTI-TIPPER Invacare ® Top End Reveal ™ Wheelchair 94 Part No 1171880 FIGURE 3 Reversing Anti-tipper Bracket Orientation Mounting Hole (Hidden) Release Buttons ANTI-TIPPERS BRACKET SE TTING .
NOTES Part No 1171880 95 Invacare ® Top End Reveal ™ Whe elchair NOTES.
Invacare Corporation USA One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z 4G4 Canada 800-668-5324 Part No 1171880 Rev A - 10/11 www.
An important point after buying a device Invacare 1171880 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Invacare 1171880 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Invacare 1171880 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Invacare 1171880 you will learn all the available features of the product, as well as information on its operation. The information that you get Invacare 1171880 will certainly help you make a decision on the purchase.
If you already are a holder of Invacare 1171880, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Invacare 1171880.
However, one of the most important roles played by the user manual is to help in solving problems with Invacare 1171880. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Invacare 1171880 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
