Instruction/ maintenance manual of the product JC199 Hanns.G
Go to page of 20
JC199.
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interfer ence S tatement This equipment has been tested and found to comp ly with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User’s Manual Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is de signed, manufactured and tested according to some of the stri ctes t quality and environmental requirements in the world.
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environment prot ection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.
User’s Manual T ABLE OF CONTENTS SAFETY NOTICE ...................................................................................................... 6 PRECAUTIONS .....................................................................................
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the pa rty responsible for compliance could void the user's authority to operate the equipm ent. 2. Shielded interface cables and AC pow er cord, if any , must be used in order to com ply with the emission limits.
User’s Manual SPECIAL NOTES ON LCD MONIT ORS The following symptoms are norm al with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the s creen may flicker during initial use. T urn of f the Power Switch and then turn it on again to make sure the flicker disappears.
User’s Manual BEFORE OPERA TING THE MONITOR FEA TURES • 19” TFT Color LCD Monitor • Crisp, Clear Display for W indows • Recommended Resolutions : 1280 X 1024 @60Hz • EP A ENERGY ST AR ® .
User’s Manual INST ALLA TION INSTRUCTIONS INST ALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer secti on of the base points forward. 3. Snap the monitor into its base.
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC T urn off your computer before perform ing the procedure below . 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer ’ s D-Sub port.
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monito r , and then adjust the monitor ’ s angle to your own preference. • Hold the stand so you do not topple the mon itor when you change the monitor ’ s angle.
User’s Manual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control butt ons are located on the front panel of the monitor (See Figu re 4). By changing these settings, the picture can be adjuste d to your personal preference.
User’s Manual FRONT P ANEL CONTROL • Power Button: Press this button to switch ON/OFF monitor ’ s power . • Power Indicator: Green — Power On mode. Orange — Power Saving mode. • MENU / RETURN: 1. T urn the OSD menu on/of f or re turn to the previous menu.
User’s Manual HOW T O ADJUST A SETTINGS 14 BRIGHTNESS/CONTRAST BRIGHTNESS Adjust the brightness value of the display according to your preference. Select 「 BRIGHTNESS 」 option to adjust the brightness value. CONTRAST Adjust the contrast value of the display according to your preference.
User’s Manual 15 H-POSITION Select the 「 H-POSITION 」 option to shift the screen im age to the left or right. Enter the option and adjust the level. [For VGA only] V -POSITION Select the 「 V -POSITION 」 option to shift the screen image up or down.
User’s Manual PLUG AND PLA Y PLUG & PLA Y DDC2B FEA TURE This monitor is equipped with VESA DDC2B c apa bilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depe nding on the level of DDC used, communicate additional information about its display capabilities.
User’s Manual TECHNICAL SUPPOR T (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position *Power Cord shoul.
User’s Manual identified. *Make sure the System > Silence option in the monitor menu is on. 18.
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly conne cted, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage.
User’s Manual APPENDIX SPECIF ICA TIONS Driving system TFT Color LCD Size 19.0" LCD Panel Pixel pitch 0.294mm(H) x 0.294mm(V) H-Frequency 31KHz – 80KHz V i deo V -Frequency 55 – 75Hz Display Colors 16.
An important point after buying a device Hanns.G JC199 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hanns.G JC199 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hanns.G JC199 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hanns.G JC199 you will learn all the available features of the product, as well as information on its operation. The information that you get Hanns.G JC199 will certainly help you make a decision on the purchase.
If you already are a holder of Hanns.G JC199, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hanns.G JC199.
However, one of the most important roles played by the user manual is to help in solving problems with Hanns.G JC199. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hanns.G JC199 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
