Instruction/ maintenance manual of the product Z8800 Series Electrolux
Go to page of 16
Upright Vacuum Cleaner Owner’s Guide Household Type Z8800 Series IMPORTANT For any advice on your cleaner and to order filters and accessories, please telephone the Electrolux Helpline on 08706 055055 FILTER REPLACEMENT CODE: EF105 and EF106 www.electrolux.
2 IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces.
3 BEFORE YOU START CHECK THE VOLTAGE Before connecting the cleaner to an electrical supply, ensure that the voltage shown on the rating plate located beneath the cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer.
4 SERVICE Should you require service on your Electrolux cleaner, please telephone Electrolux Customer Services on 08706 055055. Before requesting service, please check whether your problem is covered under Service Checklist (see below). New filter pads, brushrolls and drive belts can be obtained from Electrolux Retailers.
5 HOW TO IDENTIFY PARTS OF CLEANER Items in Carton cleaner body handle hose clip screws (4 in bag) dusting brush combination crevice tool & nested wand turbo nozzle (on.
6 HOW TO ASSEMBLE cont. Step 3: Move the hose out of the way before the next step (Step 4) as shown. Step 4: Attach the tool caddy by inserting the tab as shown, and rotating it forward. Step 5: Fasten the tool caddy with 2 screws. The left screw will need to be fastened as shown (through the hole in the tool caddy’s hose guide).
7 HOW TO ASSEMBLE cont. Step 9: Store the dusting brush behind the handle as shown. Step 10: Store the turbo nozzle on the front of the cleaner, above the dust cup, as shown. Push to lock in place. Helpful Hints: Use caution when using this vacuum on area rugs.
8 HOW TO USE CLEANER cont. Warning: to avoid injury, keep loose clothing, fingers, hair, etc. away from moving brushroll. 4) Set Cleaner Height Setting from High setting for long pile to Low for short pile. Note: If cleaner is hard to push, move selector to next highest setting.
9 HOW TO USE ACCESSORIES cont. Warning: To reduce the risk of injury from a falling cleaner, always work with the cleaner below you, pushed against the bottom step. Caution: Do not place the cleaner on the stairs as this may cause carpet damage. HOW TO USE ACCESSORIES cont.
10 HOW TO USE ACCESSORIES cont. 6) Self Cleaning Duster (on some models) - How To Clean: Secure the duster into the Duster Tube, and rotate the Duster Activation Knob counterclockwise (towards the back of the vacuum) to clean the duster.
HOW TO MAINTAIN cont. 3) Check the HEPA EF105 Exhaust Filter: Empty the dust cup and do not place it back in the vacuum; lay the vacuum flat on the floor. The HEPA filter is accessed by removing the foam filter & frame, and turning the knob left. Remove the HEPA filter door completely, and brush off or replace the HEPA filter.
HOW TO MAINTAIN cont. How to Clear Blockages in Hose Caution: Make sure On/Off switch is in Off (o) position and power supply cord is unplugged before servicing. 1) Firmly pull the end of the hose from the hose retainer on the back of the vacuum. 2) Check for blockages in the hose and hose retainer.
HOW TO MAINTAIN cont. Caution: Make sure On/Off switch is in Off (o) position and power supply cord is unplugged before replacing belt. Belt pulley can become hot during normal use. To prevent injury, avoid touching the motor shaft when checking the belt.
Problem Solving CAUTION: Turn off the switch and unplug the electrical cord before servicing. Problem Cause Solution Motor will not start. Power Plug On/Off Switch Thermal Cut Off • Push plug securely into outlet. • Try another outlet. • Check circuit breaker.
Problem Cause Solution Motor will not start. Power Plug On/Off Switch Thermal Cut Off • Push plug securely into outlet. • Try another outlet. • Check circuit breaker. • Turn on/off switch to |. • Refer to page 2. Motor suddenly stops. Thermal Cut Off • Refer to page 2.
Part No. 79316 (0X/07) Printed in PRC If you experience any problems with your cleaner, don’t struggle taking it back to the shop. Call our dedicated Customer Helpline for help and advice on 08706 055055 Thank you for purchasing an Electrolux cleaner.
An important point after buying a device Electrolux Z8800 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux Z8800 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux Z8800 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux Z8800 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux Z8800 Series will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux Z8800 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux Z8800 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux Z8800 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux Z8800 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
